Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
SAE 30 OR 10W30 MOTOR OIL LUBRICATION ** REFER TO MAINTENANCE "ENGINE " Keep unit well lubricated (See "LUBRI SECTION. CATION CHART"). 11 _,CAUTION: Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cylinder fins as contact may cause bums. ENGINE LUBRICATION Use only high quality detergent oil ratedwith API service classification SF-SJ. Select the oil's SAE viscosity grade according to your expected temperature. __SAE VISCOSITY (3RAD.S NOTE: Although multi-viscosity oils (5W30, 10W-30, etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F (0°C). Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tiller is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Add SAE 30 motor oil or equivalent. Tighten oil filler plug securely each time you check the oil level. TO CHANGE ENGINE OIL Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ. • Be sure tiller is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. 1. Remove drain plug. 2. Tip tiller forward to drain oil. 3. After oil has drained completely, replace oil drain plug and tighten securely. 4. Remove oil filler plug. Be careful not to allow dirt to enter the engine. 5. Refill engine with oil. See "FILL ENGINE WITH OIL" in the Operation section of this manual. Plug\ ,,_1_ "Oil Filter __.J Plug AIR CLEANER Service air cleaner cartridge every twenty-five hours, more often if engine is used in very dusty conditions. 1. Loosen air cleaner screw. 2. Remove air cleaner cover. 3. Carefully remove air cleaner cartridge. Be careful. Do not allow dirt or debris to fall into carburetor. 4. Clean by tapping gently on a flat surface. NOTE: If very dirty or damaged, replace cartridge. 5. Clean and replace cover. Tighten screw securely. _CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge. Cover Air Cleaner COOLING SYSTEM Your engine is air cooled. For proper engine performance and long life keep your engine clean. • Clean air screen frequently using a stiff-bristled brush. • Remove blower housing and clean as necessary. • Keep cylinder fins free of dirt and chaff. 12 r Fins Muffler Housing MUFFLER Do not operate tiller without muffler. Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically and replace if necessary. If your engine is equipped with a spark arrester screen assembly, remove every 50 hours for cleaning and inspection. Replace if damaged. SPARK PLUG Replace spark plugs at the beginning of each tilling season or after every 50 hours of use, whichever comes first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" on page 4 of this manual. TRANSMISSION Your transmission is sealed and will not require lubrication unless serviced. CLEANING Do not clean your tiller when the engine and transmission are hot. We do not recommend using pressurized water (garden hose, etc.) to clean your unit unless the gasket area around the transmission and the engine muffler, air filter and carburetor are covered to keep water out. Water in engine will shorten the useful life of your tiller. • Clean engine, wheels, finish, etc. of all foreign matter, • Keep finished surfaces and wheels free of all gasoline, oi!, etc. • Protect painted surfaces with automotive type wax. _I, CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TILLER TO ADJUST HANDLE HEIGHT Factory assembly has provided lowest handle height. Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil. 1. If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets. 2. Slide handle panel to desired location. 3. Tighten the four nuts securely. Engine Brackets andle Panel Nuts(Also 2 o_llLt:r Side TINE ARRANGEMENT Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs. _CAUTION: Tines are sharp. Wear gloves or other protection when handling tines. NORMAL TILLING -26" PATH • Assemble holes =A" in tine hubs to holes "B" in tine shaft. _--Clevis Pin Outer 7 HairpinClip MID-WIDTH TILLING -24" PATH • Assemble holes ...