Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Authorized service shall be sought if a problem exists. 24. Do not touch engine parts which may be hot from operation. Let parts cool down sufficiently. 25. Please remember: You can always stop the tines and wheels by releasing the Forward Clutch Lever or the Maneuvering Clutch Lever (whichever lever you have engaged) or by moving the Throttle Control Lever to STOP. 26. To load or unload the tiller, see the instructions in Section 4 of this Manual. 27. Use extreme caution when reversing or pulling the machine towards you. 28. Start the engine carefully according to instructions and with feet well away from the tines. 29. Never pick up or carry a machine while the engine is running. Maintenance and Storage 1. Keep the tiller, attachments and accessories in safe working condition. 2. Check all nuts, bolts, and screws at frequent intervals for proper tightness to be sure the equipment is in safe working condition. 3. Never store the tiller with fuel in the fuel tank inside a building where ignition sources are present such as hot water and space heaters, furnaces, clothes dryers, stoves, electric motors, etc. Allow engine to cool before storing in any enclosure. 4. To reduce the chances of a fire hazard, keep the engine free of grass, leaves, or excessive grease. 5. Store gasoline in a cool, well-ventilated area, safely away from any spark- or flame-producing equipment. Store gasoline in an approved container, safely away from the reach of children. 6. Refer to the Maintenance sections of this Manual and the separate Engine Owner’s Manual for instructions if the tiller is to be stored for an extended period. 7. Never perform maintenance while the engine is running or the spark plug wire is connected, except when specifically instructed to do so. 8. If the fuel tank has to be drained, do this outdoors. 4 Section 1: Safety Decals For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1 below). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing. Refer to the separate parts catalog for decal locations, part numbers and ordering instructions. Tine Warning (on right side of hood flap) Starting Stabilization Message (on engine) Control Descriptions (on control Panel) Warning Messages (on tine hood) Hot Surfaces/Moving Belts Warning (on belt cover) Figure 1: Location of Safety and Operating Decals Operating Symbols H 111 CHOKE CHOKE ON OFF R Various symbols (shown here, with word descriptions) may be used on the tiller and REVERSE $ engine. ROTATING % -a ® — O— TINES FAST SLOW STOP TILLER DIRECTION LEVER DIRECTION A WARNING TO AVOID SERIOUS INJURY: • READ THE OWNER’S MANUAL. • KNOW LOCATIONS AND FUNCTIONS OF ALL CONTROLS. • KEEP ALL SAFETY DEVICES AND SHIELDS IN PLACE AND WORKING. • NEVER ALLOW CHILDREN OR UNINSTRUCTED ADULTS TO OPERATE TILLER. • SHUT OFF ENGINE AND DISCONNECT SPARK PLUG WIRE BEFORE MANUALLY UNCLOGGING TINES OR MAKING REPAIRS. • KEEP BYSTANDERS AWAY FROM MACHINE. • KEEP AWAY FROM ROTATING PARTS. • USE EXTREME CAUTION WHEN REVERSING OR PULLING THE MACHINE TOWARDS YOU. 5 Section 2 Assembly A WARNING To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this manual. Introduction Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. Inspect unit Inspect the unit and carton for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the damage and request instructions for filing a claim. To protect your rights, put your claim in writing and mail a copy to the carrier within 15 days after the unit has been delivered. Contact us at the factory if you need assistance in this matter. STEP 1: Unpacking Instructions 1. Remove any cardboard inserts and packaging material from the carton. Remove any staples from the bottom of the carton and then lift the carton up and off the unit. 2. The tiller is heavy and you should not attempt to remove it from the shipping platform until the handlebars are installed and the Wheel Gear Lever is placed in DISENGAGE. The procedure for removing the tiller is explained in Step 2 of these assembly steps. 3. Remove the handlebar assembly from the carton. Do not remove the two control levers from the handlebars. 4. Remove the separate hardware bag from the carton. Check that you have the items listed below and shown in Fig. 2-1. Contact your local dealer or the factory if any items are missing or damaged. Hardware Parts List Fig. Ref. Qty. Description 1 1 Height Adjustment Handle 2 1 Keyed Washer 3 4 Plastic Tie Strap 4 3 Hairpin Cotters 5 2 3/8"-16 x 1“ ...