Log:
Assessments - 1, GPA: 4 ( )

Instruções de Operação Land Pride, Modelo 11052x4NC

Fabricante : Land Pride
Arquivo Tamanho: 834.08 kb
Arquivo Nome : abddaf3c-741f-4553-a4c1-7c385f0e4159.pdf
Língua de Ensino: enesfr
Ir para baixar



Facilidade de uso


Squeeze the throttle control all the way up against the hand grip. The engine is governor controlled and must be run at full throttle while tilling. 3. Hold the handle firmly and slowly tilt the unit forward to begin the tilling action. 4. As the tines begin to make contact with the ground, hold back on the handles so that the tines will dig into the soil and not ride forward over the ground. 5. Avoid tilling soil that is too dry as it will pulverize and produce a dust that will not hold water. Also, tilling soil that is too wet will be hard on the machine and produce unsatisfactory clods. 6. Lowering the depth stake will slow the cultivator and make it till deeper. Raising the depth bar will allow it to move faster and till more shallow. See “How To Set The Depth Stake or Depth Rod”. WARNING: Keep away from the rotating tines. Rotating tines can cause injury. F–041306C 12 OPERATION BEFORE STARTING THE ENGINE How To Prepare The Engine WARNING: Always use a safety fuel container. Do not smoke when adding the fuel mixture to the engine. When inside an enclosure, do not fill the fuel tank. Before you add the fuel mixture, stop the engine. Let the engine cool for several minutes. How To Mix The Fuel Mixture The two cycle engine, used on this cultivator, requires a mixture of gasoline and oil for lubrication of the bearings and other moving parts. The correct fuel mixture ratio is 24:1 (5.3 oz. oil per one gallon of gas – see the Fuel Mixture Chart). Gasoline and oil must be pre–mixed in a clean gasoline container. Always use fresh, clean, unleaded gasoline. Mix gasoline and oil as follows: 1. Pour one (1) U.S. quart of fresh, clean, unleaded automotive gasoline into a one gallon size gasoline container. 2. Add 5.3 ounces of clean, high quality, two–cycle oil to the gasoline container. IMPORTANT: Do not use outboard motor oil or multi–viscosity oils,such as 10W–30 or 10W–40. 3. Install the fuel cap onto the gasoline container. Vigorously shake the gasoline container to mix the oil with the gasoline. 4. Add an additional three (3) U.S. quarts of gasoline to the gallon container. Again shake the gasoline container. 5. This completes the gasoline mixing procedure. The gasoline can now be added to the fuel tank. FUEL MIXTURE CHART (mixture 24:1) U.S. SI. (Metric GAS OIL GAS OIL 1 Gal. 5.3 oz. 4 Liters .167 L 2 Gal. 11 oz. 8 Liters .333 L 5 Gal. 27 oz. 20 Liters .833 L Do not fill the fuel tank with gasoline that does not have oil mixed in it. Shake the gasoline container before each filling of the fuel tank. Add more gas (3 U. S. Quarts) 1 U.S. Gallon Special Gasoline 1 U.S. Gallon container F–041306C 13 OPERATION HOW TO START THE ENGINE Before you start the engine, make sure that you have read and understand all the instructions on the preceding pages. 1. Fill the fuel tank to 1/2 inch below the bottom of the fill neck. Reinstall the fuel tank cap securely. Always use fresh fuel. Never use fuel that could be stale from long periods of storage. 2. Move the Shut-off switch to the ON position (see Figure 11). 3. If the engine is cold, move the choke control to the Full Choke position (all the way down). NOTE: Do not choke a hot or warm engine. 4. Put the unit firmly on the tines and depth stake, or wheels, in an open area. 5. Hold the right handle firmly with your left hand. 6. Hold the rope handle with your right hand and pull to start the engine. Repeat if necessary. (It is sometimes necessary to hold the throttle control lever against the hand grip with your left hand. As soon as the engine starts, slowly release the throttle control. If released too slowly, the unit will sometimes move forward). 7. When the engine starts, move the choke lever to the Half Choke position. When the engine runs smoothly, move the choke lever to the No Choke position. NOTE: If the tines do not stop when the throttle control is released, adjust the carburetor idle speed. For adjustment of carburator, see the Engine Manual. 8. To stop the engine, release the throttle control and move the Shut-off switch to the OFF position. 9. If the engine becomes flooded remove and dry the spark plug. See “Spark Plug Maintenance” in the Maintenance section of this manual. Then, pull the starter rope with the choke lever in the No Choke position. WARNING: The muffler and surrounding areas become hot after running the engine. Avoid these areas. Shut-Off Switch Recoil Starter Handle Choke Control No Choke Air Cleaner Half Choke Full Choke Figure 11 F–041306C 14 OPERATION CULTIVATING TIPS . Tilling is digging in, turning over and breaking up packed soil before planting. Loose unpacked soil helps root growth. Best tilling depth is 4 to 6 inches. A tiller will also clear the soil of unwanted vegetation. The decomposition of this vegetation matter enriches the soil. Depending on the climate (rainfall and wind), it may be advisable to till the soil at the end of the growing season to further condition the soil. . Avoid tilling soil that is too dry as it will p...

Este manual também é adequado para os modelos :
Ferramentas para Jardim - 11052x4NC (834.08 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias