Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
455 Tiller Drive Assembly For eoae in attaching the tiller drive assembly to the tractor» follow the sequence of steps outlined below: 1. Fasten the belt release bracket to the outside of the side plate with the two 5/16" x 1” hex capscrews as shown in Figure 1. 2. Mount the 3" tiller drive pulley to the bovel gear shaft with Its koy, as shown in Figure l, The hub of the pulley faces In toward the tractor. Leave tho set screw loose until making final alignment, 3. Mount the tiller belt release guard to the belt release bracket as shown in 'Figure 1, The concave surface of the tiller belt release guard la to face tho bevel gear shaft. DO NOT TIGHTEN AT THIS TIME. 4. Place the 5811 long V-helt #105122 in position on the large pulley» (for ease of identification, the V-bolts ore marked with part numbers). 5. Place the 42” long V-belt #154273 in position on the smaller pulloy of the tiller drive assembly and mount the tiller drive assembly onto the Uft shaft* The arm of pulley sleeve assembly is held In place against the left side bracket of the tractor tow assembly by means of a hair pin cotter and pin. See Fig. 2. 6. Place the free end of the 5ft11 long V-belt $105122 in position on the 3" tiller drive pulley as shown in Figure 3. Note: Backside of belt is against idler pulley. 7. Plaoe the off-set end of the guide assembly rod Inio the hole In the belt release bracket and fasten In place with a hair pin cotter. See Figure 3. 3. Position the 311 pulley so that it is in line with the large pulloy of tho tiller drive assembly and tighten the setscrew securely. Pull up on the tiller clutch lever handle to engage the tiller, and adjust the belt release guard eo that clearance Is equal oaboth sfdos of the bolt. Soo Figure 3. TIGHTEN DOLTS AT THIS TIME, FIGURES. ^ g q b SIMPLICITY MANUTACTURING COMPANY. INC- The 32" Heavy Duty Tiller is shipped from the factory in one carton, Before starting to assemble the tiller, be certain to remove all of the parts from the carton. Assembly For ease in assembling the tiller, follow the sequence of steps outlined below: 1. Remove all masking tape front the ends of the Une shaft and the drive pulley shaft of the chain guard assembly, 2. To attach the deflector assembly to the chain guard assembly; remove 2 mounting bolts from each Bide of the chain guard as shown in Figures 4 & 5«. Mount the deflector so that the holes in the mounting brackets line up with the holes in the chain guard assembly as shown in Figure S., and replace the mounting bolts in their original holes, Tighten the bolts securely. FIGURE 5. 3. Assemble the left hand inner tine assembly to the left hand outer tine assembly And fasten with a pin and cotter pin. Assemble the right hand Lnner tine assemble to the right h' .d outer tine assemble, and fasten with a pin and cotter pin. NOTE: the in .<«* tine assemblies can be identified by the constant diameter of the hub fastened to the tine plate. The long end of this hub is inserted Into the long end of the hub of the outer tine assemblies and is fastened as described above. CAUTION: As itls possible to mount the tine assemblies incorrectly to the tine shaft, pay particular attention to the following; Assemble the tines to the tine shaft as shown in Figure 7. so that the sharp edges of the top tines face toward the front of the tractor. Fasten the tines to the tine shaft with a pin and cotter pin on each end of the tine shaft. When the tines are mounted, check once more to be certain that the sharp edges of all tines face in the correct direction. 4. Attach the deflector end plates. 5. Assemble the tiller drive pulley to the tiller drive shaft as shown in Figure 6. The pulloy is held In place by a key and set screw and la to be mounted with the hub of the pulley facing away from the chain ifuard. Attachment For ease In attaching the tiller to the tractor, follow the sequence of steps as outlined below; 2 1. Apply alight coat of grease to tiller lift bar, and place the tiller in position in back of the tractor. Pull the tractor lift lever to the full back position and place the tiller lift bar aa&embly into the tube of the rear lift assembly on the tractor. Fasten in place with a pin and hair pin cotter as shown Id Figure 2. Place the tractor lift lever in the forward position and connect the tiller frame to the tractor tow assembly with the pivot rod and hair pin cotters. See Fig. 8. 3. Turn the belt tension adjusting screw to the full loose position ( turn counter-clockwise ) and place the free end of the 42" long V-beU £154273 in position on the tiller drive pulley. With the V-belt in position on the tiller drive pulley and on the smaller pulley of the tiller drive assembly, turn the bait tension adjusting screw in a clockwise direction until the slack is taken out of the V-belt. If TWO-SPEED KIT IS EN5TALLED ON TRACTOR, FOLLOW STEPS 1 THROUGH 3 ONLY, 4. Depress the tractor brake pedal and lock in position. Loosen the bait guard mount...