Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Secure with two IQ-32 x 1/2 truss screws (B) and 10-32 nut/washer assemblies (C). Figure 4. A. Cover C. Clevis Pin B. Support O. Clip 8. Open cover and fasten cable {A, figure 6) to tube support (B) to prevent cover from going overcenter when opened. Loop end of cable fits over washer (C). Figure 5. A. Handle B. Truss Screw C. Nut/Washer Assemblies Figure 6. A. Cable B. Support C. Washer 9. Open grass bag cover and install grass bag frames (A, figure 7) to support brackets (B). Make sure cover handle latches to grass bag frames. 10. Install the turbo according to instructions in the turbo Operator’s Manual. Note that the belt cover and idler pulley mounting hardware for the turbo installation is packaged with the twin bagger. 11. Assemble the middle tube (A, figure 8) to the upper tube (B) with 10-32 x 1/2" trusshead screws (C, from inside), flat washers (D), and nut/washer assemblies (E). 12. Assemble the lower tube (F, figure 8) to assembled upper tube with 10-32 x 1/2" trusshead screws (C, from inside), fiat washers (D), and nut/washer assemblies (E). 13. Install the 1/4-20 x 5/8" roundhead bolt (G, figure 8) through the inside of turbo housing discharge as shown in figure 11. Secure with 1/4-20 locknut (H). On turbo housing without the pre-drilled hole (Mfg. No. 1691260 and early model 1691810), a 9/32" hole must be drilled as shown in figure 9. 14. Apply dry talc power to rubber seal at cover opening. Install tubeassemblyasfaraspossible into cover opening so that lower tube can be installed at blower opening. Latch lower tube clip onto bolt and nut {installed in step 13). Figure 7. A. Grass Bag Frame B. Support Frame A. Middle Tube E. Nut/Washer Assembly B. Upper Tube F. Lower Tube C. Trusshead Screw, 1/2" G. Roundhead Bolt, 5/8" D. Flat Washer H. Locknut с A. Turbo Housing Operation and Storage ^WARNING For safety reasons grass and debris are to be removed only after engine Is shut off, key removed, and all moving parts stopped. ^WARNING Before raising cover, shut off engine, remove key, and set parking brake. BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Clean the tube with mild detergent (other products may damage tube). Inspection windows can be removed to be cleaned. Make sure windows are securely in place before operating. Check grass condition. If wet, wait until later in the day. If grass is wet plugging may occur. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, you should remove grass and debris from underside of mower deck, discharge chute and screen inside cover. The blower housing and tube should be removed for cleaning. Remove the tube by unlatching the lower tube clip from blower housing. If desired, the bags can be lined with 30 gallon trash bags for easy disposal. Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass bag cover. OPERATION Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width to prevent clogging. If grass is high, operate with mower in high cutting position. Cut the grass again in lower cutting position, if desired. To check if grass is flowing up tube, view tube through rear inspection window. Do not open cover with mower engaged. To check if grass bags are full, reach back and feel top of right bag (left bag will fill first) or view tube discharge through front inspection window in cover. If a large amount of cut grass is spilling out from under deck, the tube may be plugged or grass bags are full. Shut off rider, disengage PTO, and allow all moving parts to stop before disconnecting tube. Always operate with throttle at full speed. EMPTYING THE BAGS NOTE Tilt seat up to allow cover to remain in “up” position. Raise the cover. If a plastic liner was not used, unhook the bag and turn inside down to empty (use handle on bottom). If plastic liner was used, first tie up top of liner. Then, either pull the liner out, or turn the bag upside down and allow the filled liner to slide out. STORAGE 1. Clean the grass catcher thoroughly. 2. If paint has been scratched on metal parts, coat with paint or oil. 3. Store in a dry area. Hang the bags to dry. Always store away from moisture. 7 Troubleshooting This section provides troubleshooting instructions for the more common and easily corrected problems. See Table 1. For problems not covered, see your dealer. ^WARNING To avoid serious Injury, perform maintenance on the grass catcher only after stopping the engine and waiting for all moving parts to come to a complete stop. Always remove the ignition key before beginning the maintenance to prevent accidental starting of the engine. Disconnect the spark plug wire and fasten away from plu...
Este manual também é adequado para os modelos :Ferramentas para Jardim - 1691792 (586.06 kb)