Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
The different operating properties are shown according to the table below: Direction Properties Left The machine works itself forward , angled to the left. Middle The machine works itself forward without being angled toeither side. Right The machine works itself forward, angled to the right. Set the depth skid vertically and turn by slackening off the screw (3:X), set the depth skid in the desired position and then tighten the screw. Remove the depth skid with mounting arm by pulling the pin (1:T) upwards. The pin is locked by a locking pin underneath. 5 OPERATION 5.1 Fuel Read and understand all safety instructions. No fires or smoking near to petrol. Use 92-95 octane lead free petrol. ENGLISH GB ENGLISH GB Oil-mixed petrol designed for 2-stroke engines must never be used. Filling Read and understand all safety instructions. If the engine has been running, wait a few minutes until it has cooled before filling up. Fill carefully to prevent the spillage of fuel. Move the rotary cultivator at least 3 metres from the filling site before starting. Fill as follows: 1. Clean around the fuel cap. 2. Unscrew the filler cap. 3. Fill using a funnel or use a filler can with spout to prevent spillage. 4. Tighten the filler cap. 5. Move the rotary cultivator at least 3 metresfrom the place of filling before starting. Move the rotary cultivator at least 3 metres from the filling site before starting. 5.2 Engine Oil Always check the oil level before starting. Otherwise there is a risk of serious engine damage. Also see “4.9” and “4.10”. Check the oil level as follows: 1. Position the machine so that the engine is horizontal. 2. Unscrew the oil filler and check that the oil level is level with the lower part of the hole’sthread. 3. Top up the oil if necessary. Use normal engine oil SAE 10W-30. 4. Reassemble the oil filler cap. Move the rotary cultivator at least 3 metres from the filling site before starting. 5.2.1 Starting the engine from cold 1. Open the fuel cock. See “4.15”. 2. Put the choke in position “CHOKE”. See “4.14”. 3. Set the throttle (1:D) in the “START” position. 4. Hold the handle with one hand and slowly pull the starter handle with the other hand. See “4.16”. When the starter mechanism engages, quickly and forcefully pull the starter handle until the engine starts. NOTE! Do not pull the cord hard to its stop position and do not release it in the pulled out position. This damages the starter mechanism. 5. Reset the choke after 3-5 seconds. 5.2.2 Starting a warm engine Start a hot engine according to points 1, 3 and 4 above. The choke must not be used. 5.3 Operating 1. Tip the rotary cultivator back slightly so that the rotor is above ground. 2. Activate the drive control (1:B). 3. Tilt the cultivator forward so that it works its way into the soil. 4. To reverse, activate reverse control (1:A). 5.4 Stop 1. Stop the rotary cultivator by setting the throttle and stop control (1:C) to “OFF”. 2. Shut off the fuel cock. See “4.15”. 5.5 Operating tips The rotors propel the machine forward. The speed of the rotors is controlled by the throttle (1:D). Keep hands and feet away from rotating parts (1:N). The optimum working depth varies with soil conditions. The working depth is determined by how hard the depth skid is pushed down during propulsion. Operate and test. Drive 2-3 times in different directions for best re sults. Never operate the machine in wet soil. Clumps of earth are created that are then difficult to break-up. Hard and dry soil requires an extra run, at right angles to the first. WARNING! Never overload a new machine. Drive carefully for the first 5 hours. 6 STORAGE Store the rotary cultivator in a dry place. Also see section “Safety instructions”. After draining the petrol, start the engine and allow it to run until it runs out of petrol. ENGLISH GB ENGLISH GB 7 MAINTENANCE WARNING!Repairs must be carried outby the dealer. Otherwise the guarantee becomes invalid. WARNING!Before carrying out repairs and maintenance, the spark plug connection must be disconnected. 7.1 Periodic maintenance Before each operation • Check for fuel leaks. • Check that all screws are tightened. After each operation • Clean the rotary cultivator. • Check for fuel leaks. Every 25 operating hours and every 3 months • Check, clean or replace the air filter. • Check that all screws and nuts are tightened. 7.2 Air filter (1:G) Do not use flammable liquids when cleaning. Serious engine damage can be caused if the machine is operated with a defective or blocked filter. The paper filter must never be cleaning with liquid. The machine is equipped with a pre-filter (foam rubber) and a main filter (paper). Clean/replace the air filter every 3 months or every 25 operating hours. During operation in dry and dusty conditions, the air filter must be cleaned/replaced every day. Clean/replace the air filter as follows: 1. Undo the screws or locking tabs and the filter housing. 2. Grasp the main filter (paper) and shake it a few times against...