Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
24666 ■ Read the Owner's Manual carefully. Be thoroughly familiar with the controls and proper use of the equipment. ■ Never allow children to operate the unit. ■ Keep the area of operation clear of all persons, particularly small children, and pets. ■ Thoroughly inspect the area where the equipment is to be used and remove all stones, wire, bones and other foreign objects. ■ Do not operate equipment when barefoot or wearing open sandals. Always wear substantial footwear. ■ Check fuel before starting engine. Do not fill gasoline tank indoors, when engine is running, or while engine is still hot. Wipe off any spilled gasoline before starting engine. * Disengage power to attachments when transporting or not in use. ■ Do not change engine governor settings or overspeed engine. ■ Do not put hands or feet near or under'rotating parts. ■ Stop tines when crossing gravel drive, walks or roads. ■ Vehicle and attachments should be stopped and inspected for damage after striking a foreign object and the damage should be repaired before restarting and operating the equipment. ■ If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble. HOMELITE warrants rotary tiller tines against breakage for the period not to exceed the normal life of the rotary tiller: and will replace broken tines directly to the customer at no charge, provided broken tines are returned prepaid to the nearest HOMELITE district office. HOMELITE a division of Textron Inc. HOMELITE1 A tflXtfOni DIVISION. PORT CHESTER. N.V. 10373 n 36 ROTARY TILLER CONTENTS SAFETY..................................................................................2 WARRANTY..........................................................................2 INSTRUCTIONS....................................................................3 LUBRICATION ....................................................................3 BELT ADJUSTMENT..........................................................3 PARTS HOUSING GROUP..................................................................4 DEFLECTOR & TINE GROUP............................................6 TILLER DRIVE GROUP......................................................8 TINE EXTENSION GROUP.............................................10 PARTS LIST..........................................................................11 2 ASSEMBLY INSTRUCTIONS BELT ADJUSTMENT 1. Position tiller at the rear of the tractor. Place the lift lever in the fully back position. Put the tiller lift assembly into the tractor lift assembly and secure with clevis pin and quick pin. 2. Place tractor lift lever in forward position. Secure the tiller frame assembly to tractor with the two clevis pins and two quick pins supplied. 3. Slide idler arm assembly onto rear lift shaft. 4. Attach lower end of idler arm assembly to hitch member with clevis pin and quick pin. 5. Assemble pulley to power take-off (PTO) shaft on bevel gear housing. Using existing cap screw, washers, and nut, secure belt stop to tractor. 6. Position belt dh pulleys and check that the belt is seated properly in the pulleys, and that the pulleys are properly aligned. LUBRICATION There are grease fittings on each housing bearing and two 90° grease fittings are on the right hand side of the housing. These fittings should be lubricated every three hours of operation. Use a good grade of general purpose automotive type grease applied with a standard grease gun. (Fittings should be wiped clean before applying any grease.) Also apply a few drops of lubricating oil to the moving linkages of the tiller drive assembly occasionally. The belt that transmits power from the bevel gear box to the tiller drive shaft is designed to provide long and satisfactory service. Because of the special design of this belt, it is urged that it is only replaced with genuine replacement ordered from your dealer. Adjustment of belt tension is controlled by the set collar on the rod guide assembly. The tensionshould be correct when there is about 1-1/4" clearance between the collar and the bracket of the rod guide assembly with the tiller clutch lever engaged. To increase the tension, release the tiller clutch lever and loosen the setscrew in the collar. Slide the collar up toward the spring and retighten the set screw. Check the tension by engaging the tiller clutch lever. Avoid excessive tension as it will cause premature belt failure. Before starting the tractor engine, place the tiller clutch lever in the disengaged position, and raise the tiller above the surface of the ground. With the tractor engine running, engage the tiller clutch and lower the tiller into contact with the ground. As the tiller works into the soil, slowly release the tractor clutch and move ahead. When coming to the end of a row, raise the tiller free of the ground before turning around. Effective operation o...