Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
Before starting to assemble the tiller, be certain to remove all of the parts from the carton. Aftsembly For ease In assembling the tiller, follow the sequence of steps outlined below; 1. Remove all masUng tape from the ends of the tine shaft and the drive pulley shaft of the chain miard assembly. 2. To attach the deflector assembly to the chain guard assembly; remove 2 mounting bolts from each side of the chain guard as shown in Figures 1& 2, Mount the deflector so that the holes in the mounting brackets line up with the holes In the chain guard assembly as shown in Figure 3, and replace the mounting bolts in their original holes. Tighten the bolts securely. 32" Heavy Duty Tiller Mfr's No. 392 3 . Assemble the loft hand Inner tine assembly to the left hand outer tine assembly and fasten with a pin and cotter pin. Assemble the right hand inner Une assemble to the right hand outer tine assembly, ¿nd fasten with a pin and cotter pin. NOTE: the inner tine assemblies can be Identified by the constant diameter of the hub fastened to the tine plate. The long end of this hub is insertedlnto the long end of the hub of the outer tine assemblies and le fastened as described above. CAUTION: As itis possible to mount the tine assemblies incorrectly to the tine shaft, pay particular attention to the following: Assemble the tines to the tire shaft shown In Figure 4 so that the sharp edges of j*Vg_ tOp lines face toward the front of the tractor. Fasten the tines to the tine shaft with a pin and cotter pin on each end of the tine shaft. When the tines are mounted/ check ones more to be certain that the sharp edges of all tines face in the correct direction. 4- Attach the deflector end plates. 5. Assemble the tiller drive pulley to the tiller drive shaft as shownlnFigure 3. The pulley is held Ln place by a key and set screw and is> to be mounted with the hub of the pulley feeing away from the chain guard. SIMPLICITY MANUFACTURING COMPANY, INC. TP -1278 Tiller Drive Assembly For ease in attaching the tiller drive assembly to the tractor, follow the sequence of steps outlined below: 1» Fasten the belt release bracket to the outside of the aide plate wtth the two 5/16 " x 1" hex capscrews as shown in Figure 5 . 2. Mount the tiller belt release guard to the belt release bracket as shown in Figure 5, The concave surface of the tiller belt release guard is to face the bevel gear shaft. 3. Mount the 3” tiller drive puUey to the bevel gear shaft with its key, as shown in Figure 5 , The hub of the pulley faces in toward the tractor. Leave the set screw loose until making final alignment. FIGURE T 4. Place the 56" long V-belt #10512!! in position On Che 3 " tiller drive pulley. (For ease of identification, the V-belts are marked with part numbers. ) BELT RELEASE CUARO -Mîv' "]|-^ • belt release I t_ BRACKET ’BELT GUARD , SUPPORT SIDE PLATE 5/1&’ X I"' HEX CAPSCREW FIGURE S 5» Place the 42" long V-belt #154273 In position on the smaller pulley of the tiller drive assembly and mount the tiller drive assembly onto the lift shaft as shown in Figure 6, As is shown in Figure 7. the arm of pulley sleeve assembly is held La place against the left side bracket of the tractor tow assembly by means of a hair pin cotter and pin. Place the free end of the 56" long V-belt #105122 in position on the large pulley of the tiller drive assembly as shown in Figure 6. Position the 3“ pulley so that it is in line with the large pulley of the tiller drive assembly and tighten the set screw securely. 5. Place the off-set end of the guide assembly rod into the hole in the belt release bracket and fasten in place with a hair pin cotter* See Figure 6. 2 Attachment Lubrication For ease in attaching the tiller to the tractor, follow the sequence of steps as outlined below; 1. Place the tiller in position in back of the tractor. Pull the tractor lift lever to the full back position and place the tiller lift bar assembly into the tuba of the rear llflassembly on the tractor. Fasten in place with a pin and hair pin cotter as shown in Figure 8. 2» Place the tractor lilt lever In the forward position and connect the tiller frame to the tractor tow assembly with the pivot rod and hair pin cotters, See Fig. 6. 3. Turn the belt tension adjusting screw to the full loose position ( turn counter-clock wise ) and place the free end of the 42 M long V-belt £154273 in position on the tiller drive pulley. With the V-belt in position on the tiller drive pulley and on the smaller pulley of the tiller drive assembly, turn the belt tension adjusting screw in a clockwise direction until the slack is taken out of the V-belt, 4. Pull up on the tiller clutch lever handle to engage the tiller, and adjust the belt release gruard so that clearance is equal on both sides of the belt. See Figure 6. 5. Depress the tractor brake pedal and lock in position. Loosen the belt guard mounting bolt on the right hand side of the tractor and swing the belt guar...