Assessments - 0, GPA: 5
(
)
)
|
Facilidade de uso
. : Start the engine. : Put on the shoulder strap. Never throw cuttings into the household garbage can – they Working position Hold the control handle with your right hand, and the drive tube with your left hand. Your left arm should be extended to the most comfortable position. The most convenient working position is a tool angle of 60°, but any lesser angle may be used to suit the situation concerned. Cross-cutting can be composted! Never stand directly under the branch you are cutting – be wary of falling branches. Note that a branch may spring back at you after it hits the ground! 402BA012 KN To avoid pinching the bar in the cut, 390BA052 KN position the cutting attachment with the Cutting sequence hook against the branch and then perform the cross-cut from the top To allow branches a free fall, always cut downwards. the lower branches first. Prune heavy branches (large diameter) in several controllable pieces. The shaft should always be held at an angle of 60° or less! HT-KM 13 14 English / USA HT-KM Relieving cut : To avoid tearing the bark on thick branches, always start by performing a relieving cut (1) on the underside of the branch. : To do this, apply the cutting attachment and pull it in an arc across the bottom of the branch (see illustration). : Locate the hook against the branch and then perform the cross-cut (2). Flush-cutting thick branches : If branch diameter is more than 4“ (10 cm), first perform undercut (3) and then cross-cut at a distance (A) of about 8“ (20 cm) from the final cut. Then carry out the flush-cut (4), starting with a relieving cut and finishing with a cross-cut. Cutting above obstacles The unit's long reach makes it possible to prune branches that are overhanging obstacles, such as rivers or lakes. The tool angle in this case depends on the position of the branch. 2 1 390BA041 KN 4 3 A 390BA024 KN 402BA013 KN HT-KM 15 English / USA Cutting from a lift bucket The unit's long reach enables cutting to be performed next to the trunk without the risk of the lift bucket damaging other branches. The tool angle in this case depends on the position of the branch. : 30° angle drive (special accessories) The angle drive keeps the cutting attachment at an angle of 30° to the drive tube. The angle drive may be adjusted on the drive tube to the following positions only: : For cutting vertical branches and bushes, horizontally (1) : For a better view of the cutting attachment (2) 402BA014 KN 1 2 390BA053 KN Eng lish / USA Approved KombiEngines Only use KombiEngines supplied by STIHL or expressly approved by STIHL for use with the KombiTool. This KombiTool may be operated only in combination with the following KombiEngines: STIHL KM 55 R, KM 55 RC, KM 90 R, KM 85 R, KM 110 R, KM 130R The KombiTool may also be mounted to STIHL brushcutters with a split boom or drive tube (T models). Operation of this KombiTool is therefore also permitted on the following power tool models: STIHL FS 55 RT, FS 55 RTC, FS 85 RT, FS 83 RT Mounting the Pole Pruner Mounting the Gearbox Pull the protective caps off the ends of the drive tube and keep them in a safe place. A 402BA002 KN : Apply a mark to the drive tube at a distance A of 50 mm (2“ ) . 2 402BA023 KN 1 : Push the gearbox ( 1) onto the drive tube ( 2) as far as stop – turn the gearbox back and forth until the square end of the shaft engages. The gearbox is correctly positioned if it reaches or covers the mark ( see arrow) . 402BA024 KN 3 3 1 : Insert clamp screws ( 3) as far as stop. : With the engine is resting on the machine support, line up the gearbox ( 1) so that the clamp screws face up and the chain sprocket cover is exactly vertical. : Tighten down the clamp screws ( 3) in the following sequence: – tighten the left screw moderately – tighten the right screw moderately – tighten down the left screw firmly – tighten down the right screw firmly 16 HT-KM English / USA Mounting the KombiTool Mounting the Bar and Chain : Engage lug ( 1) on drive tube in slot ( 2) in the coupling sleeve and : Unscrew nut and take off cover. The chain is very sharp – wear work gloves to protect hands from cuts. 002BA132 KN 12 4 3 002BA133 KN 390BA042 KN 1 2 390BA043 KN390BA003 KN : push home the drive tube as far as stop. When correctly installed, the red line ( 3) (arrow point) must be flush with the end of the coupling sleeve. : Turn tensioning screw ( 1) counterclockwise until the tensioning nut ( 2) butts against the left end of the housing slot, then back it off 5 full turns. : Fit the chain – start at the bar nose. : Tighten the wing screw ( 4) firmly. : Reverse the above sequence to remove the drive tube. HT-KM 17 English / USA Tensioning the Saw Chain Checking Chain Tension 15 390BA044 KN4 3 1 390BA045 KN390BA046 KN : Fit guide bar over the stud ( 3). Engage peg of tensioner slide in locating hole ( 4) – place the chain over sprocket ( 5) at the same time. : Now turn tensioning screw ( 1) clockwise until there is very little chain sag on the underside of th...
Este manual também é adequado para os modelos :Ferramentas para Jardim - HT-KM (1.61 mb)