Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
(Apply grease on smooth side of handle lock to aid in keeping lock in place until handle assembly is lowered into position.) Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. Rotate handle assembly down. Insert rear carriage bolt first, with bolt head on L.H. side of tiller and loosely assemble locknut (See Fig. 5). Insert pivot bolt in front part of plate and tighten. Cut down remaining corners of carton and lay panels flat. Lower the handle assembly. Tighten nut on carriage bolt so handle moves with some resistance. This will allow for easier adjustment. Place flat washer on threaded end of handle lock lever. Insert handle lock lever through handle base and gearcase. Screw in handle lock lever just enough to hold lever in place. Insert second handle lock (with teeth inward) in the slot of the handle base (just inside of washer). With handle assembly in lowest position, securely tighten handle lock lever by rotating clockwise. Leaving handle assembly in lowest position will make it easier to remove tiller from carton. 6 ASSEMBLY CONNECT SHIFT ROD (See Fig. 6) • Insert end of shift rod into hole of shift lever indicator. • Insert hairpin clip through hole of shift rod to secure. FIG. 6 REMOVE TILLER FROM CRATE • Make sure shift lever indicator is in “N” position (See Fig, 6) • Tilt tiller forward by lifting handle. Separate cardboard cover from leveling shield. • Rotate tiller handle to the right and pull tiller out of carton. ATTACH CLUTCH CABLE "See Fig. 7) • Hook end of clutch cable through hole in control bar bracket if necessary. END OF CLUTCH CABLE CONTROL BAR BRACKET CONTROL BAR BRACKET CLUTCH CABLE FIG. 7 CHECK TIRE PRESSURE The tires on your unit were overinflated at the factory for shipping purposes. Correct and equal tire pressure is important for best tilling performance. • Reduce tire pressure to 20 PSI (1.4 kg/cm2). HANDLE HEIGHT • Handle height may be adjusted to better suit operator. (See “TO ADJUST HANDLE HEIGHT” in the Service and Adjustments section of this manual). 7 OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAF JLES BEFORE OPERATING YOUR TILLER. Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. ' These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. FNRA© -fe TILLING FORWARD NEUTRAL REVERSE CAUTION ENGINE ENGINE FAST OR WARNING ON OFF SLOW CHOKE FUEL OIL O FIG. 8 MEETS ANSI SAFETY REQUIREMENTS Our tillers conform to the safety standards of the American National Standards Institute. THROTTLE CONTROL - Used to control engine speed. DRIVE CONTROL BAR - Used to engage tiller. DEPTH STAKE - Controls depth at which tiller will dig. LEVELING SHIELD - Levels tilled soil. OUTER SIDE SHIELD - Adjustable to protect small plants from being buried. SHIFT LEVER - Used to shift transmission gears. RECOIL STARTER HANDLE - Used to start the engine. CHOKE CONTROL - Used when starting a cold engine. 8 OPERATION ^The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask over spectacles or standard safety glasses. HOW TO JbE YOUR ЛИ к к Know how to operate all controls before adding fuel and oil or attempting to start engine. ■ STOPPING (See Fig. 9) TINES AND DRIVE • Release drive control bar to stop movement. • Move shift lever to “N” (neutral) position. ENGINE • Move throttle control to “STOP” position. If equipped with stop switch, move switch to “STOP” position. • Never use choke to stop engine. i l TH STAKE |iee Fig. 10) The depth stake can be raised or lowered to allow you more versatile tilling and cultivating, or to more easily transport your tiller. TILLING (See Fig. 11) • Release depth stake pin. Pull the depth stake up for increased tilling depth. Place depth stake pin in hole of depth stake to lock in position. • Place shift lever indicator in till position. • Hold the drive control bar against the handle to start tilling movement. Tines and wheels will both turn. • Move throttle control to “FAST’ position for deep tilling. To cultivate, throttle control can be set at any desired speed, depending on how fast or slow you wish to cultivate. IMPORTANT: ALWAYS RELEASE DRIVE CONTROL BAR BEFORE MOVING SHIFT LEVER INTO ANOTHER POSITION. TINE OPERATION - WITH WHEEL DRIVE • Always release drive control bar before moving shift lever into another position. • Tine movement is achieved by moving shift lever to (K)tiil position and engaging drive control bar. FORWARD-WHEELS ONLY/TINES STOPPED • Release drive control barand move shift lever indicator to “F” (forward) position. E...