Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
OTHER STATES MAY HAVE SIMILAR LAWS. FEDERAL LAWS APPLY ON FEDERAL LANDS. SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT FOR SPARK ARRESTER. TABLE OF CONTENTS SAFETY RULES ...........................................................2 PRODUCT SPECIFICATIONS....................................... 3 CUSTOMER RESPONSIBILITIES......................3,10-12 ASSEMBLY................................................................ 4-5 OPERATION............................................................... MAINTENANCE SCHEDULE.......................................10 SERVICE & ADJUSTMENTS ..................................12-14 STORAGE ...................................................................15 TROUBLESHOOTING.................................................16 REPAIR PARTS-TILLER ....................... 17-22 WARRANTY .......................................................................................23 3 ASSEMBLY Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of yourtillerall parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) Utility knife (1) Screwdriver (2) 1/2" wrenches OPERATOR’S POSITION (See Fig. 1) When right or left hand is mentioned in this manual, it means when you are in the operating position (standing behind tiller handles). FRONT LEFT RIGHT OPERATOR'S POSITION FIG. 1 CONTENTS OF HARDWARE PACK §MM §N■1 (2) Hex Bolts 5/16-18x3/4 (2) Hex Bolts 5/16-18x1 (4) Washers 3/8x7/8x14 g—— © 0 (2) Hex Bolts 5/16-18x1-1/4 (6) Lock Washers 5/16 (6) Hex Nuts 5/16-18 4 ASSEMBLY UNPACK CARTON & INSTALL HANDLE (See Fig. 2) A CAUTION: Be careful of exposed staples when handling or disposing of cartoning material. IMPORTANT: WHEN UNPACKING AND ASSEMBLING TILLER, BE CAREFUL NOT TO STRETCH OR KINK CABLE(S), • Cut cable ties securing handles. • Slowly lift handle assembly up, route cable(s) as shown and align handle holes with handle panel hole and slot. • Loosely assemble hardware as shown. Be sure the shorter (3/4“ long) hex bolt is assembled in lower hole of handle. Repeat for opposite side. Tighten all hardware securely. • Cut cable ties securing tiller to skid and remove tiller from skid. • Remove screws securing depth stake to skid and discard the screws. INSTALL DEPTH STAKE ASSEMBLY • Loosen nut “A”. • Insert stake support between engine bracket halves with stake spring down. • Bolt stake support to engine brackets with bolts, lock washers and nuts. Tighten securely. Tighten nut “A”. • Depth stake must move freely. If it does not, loosen FIG. 3 HANDLE HEIGHT • Handle height may be adjusted to better suit operator. (See “HANDLE HEIGHT” in the Service and Adjustments section of this manual). TILLING WIDTH • Tilling width may be adjusted to better handle yourtilling conditions (See ‘TINE ARRANGEM tNT” in the service and Adjustments section of this manual). TINE OPERATION • Check tine operation before first use. (See “TINE OPERATION CHECK” in the Service and Adjustments section of this manual). 5 OPERATION KNOW YOUR TILLER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. Compare the illustrations with yourtillerto familiarize yourself with the location of various controls and adjustments. Save this manual forfuture reference. These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their meaning. 1FNRA©©* TILLING FORWARD NEUTRAL REVERSE CAUTION ENGINE ENGINE FAST OR WARNING ON OFF SLOW STOP I I OIL V«/ CHOKE FUEL MEETS ANSI SAFETY REQUIREMENTS Our tillers conform to the safety standards of the American National Standards Institute. FORWARD TINE CONTROL - Engages tines in forward direction. REVERSE TINE CONTROL - Engages tines in reverse direction. THROTTLE CONTROL - Controls engine speed. CHOKE CONTROL - Used when starting a cold engine. DEPTH STAKE - Controls forward speed and the depth at which the tiller will dig. RECOIL STARTER HANDLE - Used to start the engine. 6 OPERATION StfEH GUSSES The operation of any tiller can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields before starting your tiller and while tilling. We recommend a wide vision safety mask for over spectacles or standard safety glasses. HOW TO USE YOUR TILLER Know how to operate all controls before adding fuel and oil or attempting to start engine. STOPPING (See Fig. 5) TINES • Release forward tine control to stop forward movement. • Release reverse tine control to stop reverse movement. ENGINE • Move throttle control to “STOP” position. • Never use choke to stop engine. FORWARD TINE CONTROL REVERSE IN “OFF” (UP) POSI...