Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
6542.175 the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M9 6 8508 REV. 1.3 Recommended tools Screwdriver Channel Locks Adjustable Wrench Tubing Cutter SPOUT OR BASE ASSEMBLY CAUTION Turn off water at main supply. Insert SPOUT SHANK (1) through center hole of mounting surface, making sure RUBBER GASKET (2) is properly positioned in SPOUT BASE (3). Assemble RUBBER WASHER (4), BRASS WASHER (5), and LOCKNUT (6) onto threads of SPOUT SHANK (1) from underside of mounting surface. Align SPOUT (7) and tighten LOCKNUT (6). Be sure slot in BRASS WASHER (5) is positioned to the rear as shown. 1a TO CHANGE SPOUT TO A SWIVEL SPOUT: Unscrew SPOUT NUT (8) and remove SPOUT (7). Take SPOUT CLIP (9) off SPOUT (7) and remove RUBBER RING (10). Replace RUBBER RING (10) with seperate PLASTIC RING (11) packed with faucet Put SPOUT CLIP (9) on SPOUT (7). Reassemble SPOUT (7) to SPOUT BASE (3). 3 7 8 10 9 11 pog 1 2 VALVE ASSEMBLY Install LOCKNUTS (1), BRASS WASHERS (2) and RUBBER WASHERS (3) onto valve shanks Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5) into mounting holes from underside of ledge. Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is properly seated on SHANK (7). Push COUPLING (9) into TEE (6) and attach to SPOUT SHANK (7) and tighten. Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto valves until snug against internal stop. Tighten LOCKNUT (1) to secure VALVE (5) position. Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten COUPLING NUT (14) firmly. Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of right VALVE using appropriate connector. 10 11-C5 3 5/16'' MIN. - 11 5 10 MOUNTING SURFACE DRAIN ASSEMBLY (6542.140/.170) PUTTY Apply a bead of PUTTY around underside of DRAIN FLANGE (1) flange. Insert DRAIN PLUG (2) into SINK drain hole. Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4), and LOCKNUT (5) from underneath sink. Apply sealant to threaded end of TAILPIECE and thread into lower end of DRAIN PLUG. Connect other end to trap. 2 1 HOT INSTALL HANDLES ■7 6 3 4^3) 5 6 SINK 2 SEALANT Turn VALVES (1) to off position. Insert ADAPTOR (8) with larger diameter over the VALVE STEM (4). Align LEVER (2) or WRIST BLADE HANDLE (3) and install onto VALVE STEM (4). Insert BLUE INDEX (5) into cold valve (right side) and red INDEX (6) into hot valve (left side). Insert HANDLE SCREW (7) into HANDLES and tighten with screwdriver. 2 TEST INSTALLED FAUCET Remove AERATOR. With handle in OFF position, turn on water supplies and check all connections for leaks. Operate both handles to flush water lines thoroughly, spout mounting and hose connections for leaks. Turn handles into OFF position and replace AERATOR. Chec...
Este manual também é adequado para os modelos :Canalização - MONTERREY 6542.175 (119.77 kb)
Canalização - MONTERREY 6542.175 (119.77 kb)
Canalização - MONTERREY 6542.175 (119.77 kb)