Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. 1 1 1 Introduction Congratulations on your purchase of the 24-Port 10/100/1000Mbps Green Switch! It is an easy-installed network switch which helps you to extend your network structure quickly and reliably. Purpose This Quick Installation Guide tells you how to install your Switch and how to connect it to your Ethernet network. Terms/Usage In this manual, the term “Switch” (first letter upper case) refers to your 24-Port 10/100/10000Mbps Green Switch, and “switch” (first letter lower case) refers to other Ethernet switches. 1.1 Hardware Interface • 24-Port 10/100/1000Mbps auto-negotiation RJ45 Ports • All ports support auto MDI/MDIX, no need to use cross-over cables 2 1.2 Panel 1.2.1 Front Panel The front panel of the Switch consists of LED indicators, and 24 10/100/1000Mbps ports. The figure below shows the front panel of the Switch. Figure 1-1 Front Panel view of the Switch • 10/100/1000Mbps Ports (Port 1~24): These ports support 10/100/1000Mbps, and can operate in Half/Full Duplex transfer modes. These ports also support automatic MDI/MDI-X crossover detection, giving true “plug and play” capability. • LED Indicators: Comprehensive LED indicators display the status of the switch and the network (see Section 1.2.3). 3 1.2.2 Rear Panel Figure 1-2 Rear Panel view of the Switch • AC Power Connector: Supports AC 100~240V, 50~60Hz. NOTICE: Do not cover or put anything on and surrounding the switch while the Switch is operating. 1.2.3 LED indicators information The front panel LEDs provide instant status feedback and help monitoring and troubleshooting when needed. Figure 1-3 Front Panel view of the switch 4 • POWER: Power Indicator LED Color Status Solid Blinking Off POWER Green The Switch is power-on N/A No power • Port 1~24 10/100/1000Mbps Status LEDs LED Color Status Solid Blinking Off LINK/ ACT 10/100M Green The respective port is successfully connected to the 10/100Mbps Ethernet network The port is transmitting or receiving data at 10/100Mbps No link LED Color Status Solid Blinking Off LINK/ ACT 1000M Green The respective port is connected to the 1000Mbps Ethernet network The port is transmitting or receiving data at above 100Mbps No link 5 1.3 Technical Specifications Standards • IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX, IEEE802.3ab 1000BASE-T Gbit and IEEE 802.3x Flow Control Network Cables • Ethernet (10Base-T): Cables: 2-pair UTP Cat. 3, 4, 5, Twisted Pair (UTP). Up to 100m • Fast and Giga Ethernet (100/1000Base-T): 2-pair UTP Cat. 5, Twisted Pair (UTP). Up to 100m Ports • 24 x 10/100/1000Mbps Auto-Negotiation RJ45 Port Access Method • CSMA/CD Transmission Method • Store and Forward MAC Address Table • 16K Jumbo Frame • 9216-byte jumbo packet length forwarding at wire speed 6 Data Transfer Rate** • Ethernet: 10/20Mbps – Half/Full-Duplex • Fast Ethernet: 100/200Mbps – Half/Full Duplex • Giga Ethernet 1000/2000Mbps – Half/Full Duplex Physical and Environmental • Power Input: 100~240V AC, 50~60Hz • Operation Temperature: 0 °C ~ 40°C • Storage Temperature: -20°C ~ 70°C • Humidity: 5% ~ 90% RH, non-condensing 7 2 2 Installing the Switch The site where you place the switch may greatly affect its performance. When installing, take the following into your consideration. 2.1 Installation Follow the guidelines below to install the Switch: Install the Switch in a fairly cool and dry place. See the Technical Specifications for the acceptable temperature and humidity operating ranges. Install the Switch on a sturdy, level surface that can support its weight. Connect the power cord to the Switch and the power outlet. The distance is no more than 182cm. Leave at least 10cm (about 4 inches) of space at the front and rear of the Switch for ventilation. 2.2 Desktop or Shelf Installation When installing the Switch on the desktop or shelf, please attach the rubber feet to the Switch. Peel off the protective paper on the pads and attach them on the bottom of the Switch (one at each corner). 8 2.3 Rack Installation The Switch is rack-mountable and can be installed on an EIA 13-inch equipment rack. To do this, first install the mounting brackets on the Switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the Switch. 2.4 Power on the Switch The Switch has a universal power supply ranging from 100V to 240V AC, 50 ~ 60Hz power source. The AC power connector is located at the rear of the unit. The switch’s power supply will adjust to the local power source automatically. 9 3 3 Connecting the Switch This section describes how to connect the Switch to your 10/100/1000Mbps Ethernet network. 3.1 Connection Your network device (i.e. computer, switch, IP Camera, VoIP) can be connected to any port of the Switch via a two-pair UTP Category 5 Cable. If the LED indicato...