Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
The user should consult Brock Solutions or a SAF OPAL Starters supplier for clarification of the contents of this manual should any doubt or questions arise. The installation of this equipment must be conducted in accordance with all national, regional and local electrical codes. All drawings and technical representations included in this manual are for typical installations and should not in any way be considered for specific applications or modifications. Consult SAF OPAL Starters for supplemental instructions. Brock Solutions Inc. accepts no liability for any consequences resulting from inappropriate, negligent or incorrect installation, application or adjustment of this equipment. The contents of this manual are believed to be correct at the time of printing. In following with our commitment to the ongoing development and improvement of our products SAF OPAL Starters reserves the right to change the specification of this product and/or the content of this instruction manual without notice. Page3 OpalProtoModTCP Page4 OpalProtoModTCP Table of Contents INTRODUCTION ..............................................................................................6 HARDWARE ....................................................................................................6 JUMPER SETTINGS........................................................................................6 LED INDICATORS...........................................................................................7 OPAL PRO PARAMETER SETTINGS ............................................................8 I/O CONFIGURATION....................................................................................10 Page5 OpalProtoModTCP Opal Pro to Mod TCP Introduction The Opal Pro can be monitored and controlled over an Ethernet communication network using the AB Ethernet IP protocol. The Opal Pro connects to the Ethernet network through and optional Ethernet card that is mounted on the main Opal Pro control card (CA530). Access is gained to the Ethernet card via the communication opening on the right side of the Opal Pro. The Opal Pro is a AB Ethernet IP slave and is mapped as I/O through an Ethernet bridge Hardware Connection is made via a 10Mbaud Ethernet port which utilizes a RJ45 connector. Connection should be made using CAT 5 cable. Jumper Settings Jumper Setting Description J3 Not installed Boot Block write enable J4 Installed on pins 1 and 2 Disable test mode Page6 OpalProtoModTCP LED Indicators Two bi-colour (red/green) LED indicators are mounted beside the network connector. The upper LED indicates the Ethernet interface card status. LED State Ethernet Interface Card Status OFF No power Flashing Red Recoverable configuration fault (card is not configured, contact Brock Solutions for support) Solid Red Hardware Error (contact Brock Solutions for support) Flashing Green No errors client interface is not open ( check software firmware version of Opal Pro) Solid Green No errors (normal operation) Amber (Red/Green) Configuration Mode (card is not configured, contact Brock Solutions for support) The lower LED indicator indicates the Ethernet Network status. LED State Ethernet Network Status OFF Network interface offline, No network power Flashing Red I/O connection in timed-out state or other Recoverable fault Flashing Green Device in online but has no connections Solid Red Unrecoverable fault Solid Green Online with established connections Amber (Red/Green) Device is in Communication Faulted state and responding to an Identify Communication Faulted Request Page7 OpalProtoModTCP Opal Pro Parameter Settings The parameters in the Opal Pro used to configure the Ehernet interface card (group 14) are only accessible if a Ethernet interface card is installed. The parameter settings are as follows: Opal Pro Parameter Setting Description 2.02 Comm Module Ethernet Type of interface card installed (read only) 10.01 Start/Stop Comm Module This allows the Opal Pro to be started and stopped over the communication link 10.04 Iref Source Comm Module If this is set to Comm Module the Opal pro will follow the Current reference from the communication link. If there is no reference being sent on the communication link this should be set to “Internal” 10.05 Phase Angle Source Comm Module If this is set to Comm Module the Opal pro will follow the Phase Angle reference from the communication link. If there is no reference being sent on the communication link this should be set to “Internal” 14.07 Node 1 – 254 This is the Node # of the slave Opal Pro 14.08 IP Addr 1 0-255 First number in the IP address of the Opal Pro 14.09 IP Addr 2 0-255 Second number in the IP address of the Opal Pro 14.10 IP Addr 3 0-255 Third number in the IP address of the Opal Pro 14.11 IP Addr 4 0-255 Fourth number in the IP address of the Opal Pro. (the node number as set in 14.07 is added on to this number to get the final IP address) 14.12 SubNet 1 0-255 First number in the SubNet Mask 14.13 S...