Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Select DSLAM TYPE and select the name of the DSLAM type you are using. (At this point you need to back out of the menu to save the changes. The unit will need to reboot if it was not previously configured for this DSLAM type.) 2 Select DSL RATE CONFIG (BIT RATE) and change the setting to match that in your DSLAM. (If this field is read-only, allow a few seconds for autobaud to expire and the field will change to writeable.) 3 Select WAN, and then select the ATM CONFIG menu. 4 Enter the IDLE CELLS format for your network. 5 Set DATA SCRAMBLING appropriately for your network. 6 Back all the way out to the top level Total Access 600 menu, and then select the VOICE menu. (From this menu, the appropriate Voice information for working with the Voice Gateway is entered.) 7 Select CONFIG, and from the CONFIG menu, enter the Gateway type under CALL CONTROL and enter the VPI and VCI values for communicating with that Gateway. CALL CONTROL should be set to the Gateway type, and the VPI and VCI values should be set appropriately for your network. 8 To verify correct setup, use the STATUS menu (under the VOICE menu) to look at the current status of the voice connection. Under STATUS, you can view the GATEWAY STATS and information about the voice PVC along with information about the POTs ports available on the Gateway. The GATEWAY STATS menu should show the Gateway Link is up (if everything is configured correctly). A visual inspection of the VOICE LED on the front panel will also yield the status. Green = Up. Red = Down. Total Access 600 Series User Manual © 2002, ADTRAN, Inc. Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B Page 67 Appendix E. RFC1483 Quick Start (IP Routing) The Total Access 600 allows for complete integration of voice and data delivery from one compact platform (see Figure 21). Once you have completed the voice turn up procedure from the previous example, adding data to the circuit requires some additional setup. TXRX LINK V.35 RX V.35 TX DATA VOICE BATT PWR/NET Figure 21. Application Diagram To configure a Total Access 600 for IP routing, you need to know the VPI and VCI values for the data circuit on your network. You also need the IP address of the next hop router in the circuit. The table on the next page shows how to configure the Total Access 600 for IP Routing. © 2002, ADTRAN, Inc. Total Access 600 Series User Manual Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B Page 68 .. IP Routing Step 1 2 3 4 5 6 7 8 9 10 11 12 Action From the Total Access 600 main menu, select the WAN menu. (Here you set up the ATM network.) Select the ATM CONFIG menu. Enter the IDLE CELLS format for your network. Set DATA SCRAMBLING appropriately for your network. Back all the way out to the top level Total Access 600 menu, and then select the ROUTER menu. Select CONFIGURATION. From the CONFIGURATION menu, you will set up addresses for your LAN and WAN. For basic IP routing, use all the default values from the GLOBAL menu. From the ETHERNET menu, enter the IP menu to enter your LAN configuration. Enter your LAN IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY information. For this example, the IP ADDRESS is 192.168.1.2, the SUBNET MASK is 255.255.255.0, and the DEFAULT GATEWAY is 10.25.4.10. Arrow back to the main ROUTER CONFIGURATION menu, and select the WAN menu and then the ATM menu. (Here you will enter your data PVC information.) Create a new PVC by entering the menu. Enter your VPI and VCI values. From the RFC1483 IP menu, enter your LAN information. For this example, the FAR END IP ADDRESS is 10.25.4.9, the IP NETMASK is 255.255.255.252, and the LOCAL IP ADDRESS is 10.25.4.10. Arrow back to the top level Total Access 600 menu to activate your changes. Total Access 600 Series User Manual © 2002, ADTRAN, Inc. Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B Page 69 Appendix F. RFC1483 Quick Start (IP Routing with NAT) To illustrate the use of NAT, consider the example from Appendix E. To set up a single public address that will be used to access the public network, you will use the NAT menu on the WAN/ATM/RFC1483 IP menu. IP Routing with NAT Step Action 1 From the NAT menu, set NETWORK ADDRESS PORT TRANSLATION to ENABLED. (This will enable translation and allow you to enter the NAT options.) 2 Set PUBLIC IP ADDRESS MODE to SPECIFIED so you can enter your public address. During transmission, private addresses are translated into this public (NAPT) address. You will also need to set up the Translation Table to do translation on the body of the packets for certain protocols, such as FTP, to work correctly. 3 From the TRANSLATION TABLE menu, create a new entry by arrowing into the table. 4 For PUBLIC ADDRESS MODE, select NAPT ADDRESS to use the previously specified public address. 5 For PROTOCOL, select TCP. 6 Make sure that TRANSLATE BODY is set to YES. © 2002, ADTRAN, Inc. Total Access 600 Series User Manual Total Access 600 Series SHDSL IAD User Interface ...