Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Note While loading the tape, the drive will enter a false Ready Mode condition for a short period. During this false state the Tape In Use LED will continue to blink. Do not attempt any operations while the LED is blinking. When tape is unloaded. 5-8 Operation and Maintenance Table 5-4 Drive Operation LCD Messages When tape is loaded. DLTtype = DLTTM4000 (4000DLT), or DLTTM7000 (7000DLT). Compressed if compression mode enabled or Standard if compression mode disabled. 20/40GB = DLTTM4000, 35/70GB = DLTTM7000. This is the normal “Ready Screen”. If write-protected tape is inserted During loading of a write-protected tape, the display will change from: “Loading>>>” to “Write Protected Tape Inside Drive”, the LCD backlight will toggle on/off and an audible alarm will sound. Write-protected tape fully loaded. WPT = Write Protected Tape in unit. WPT will toggle to GB and back to WPT and continue toggling until next drive action. Drive Operating Conditions 5-9 Table 5-4 Drive Operation LCD Messages Whenever the system is writing to a tape, these two messages will alternate. Each message will be displayed for approximately 2.5 seconds. DLTtype = DLTTM4000 (4000DLT), or DLTTM7000 (7000DLT). Compressed if compression mode enabled, standard if compression mode disabled. Writing – indicates the system is writing to the tape. 2.1:1 – indicates the current compression ratio being used. 16GB – indicates the amount of tape still available to be written to. 3 arrows in motion ( ) – indicate tape travel. Reading – indicates the system is reading from the reading a tape, this Whenever the system is tape. message will alternate with the ready screen. Whenever a tape is in motion. Whenever an incorrect cartridge type is placed into a drive. Motion Messages = Loading, Unloading, Reading, Writing, Positioning, Erasing, Cleaning and Rewinding. 3 arrows ( ) – indicate tape travel. The LCD will flash and the beeper will sound while this message is displayed. Press the Unload button, the drive will begin unloading the tape and the LCD will return to normal operation messages. 5-10 Operation and Maintenance Table 5-4 Drive Operation LCD Messages The drive head needs cleaning or the tape is bad. followed by: If new tape, or the drive cannot initialize the tape. followed by: followed by: A hardware error occurs during normal operation. Drive Operating Conditions 5-11 5-12 Operation and Maintenance 62-0162-01 Loading the Data Cartridge Due to static the label or other items included in this package will occasionally cling to the DLT cartridge. Before loading into a drive, ensure that all other items from this package are separated from the cartridge. Never press in on the hub portion of the data cartridge. Step 1 If you are planning to write data to, or erase data from, the cartridge, make sure the Write-Protectswitch on the cartridge is in the write-enabled position (all the way to the right). A data cartridge can only be loaded when the Operate Handle LED is ON. Do not attempt to open the Cartridge Insert/Release Handle unless this LED is ON steady. Step 2 Lift up on the Cartridge Insert/Release Handle. Figure 5-1 Loading a Data Cartridge Caution Caution Step 3 Insert the data cartridge into the slot. Step 4 Push the cartridge into the drive. Step 5 Push the Cartridge Insert/Release Handle closed. The drive will go on-line. A load sequence will initiate where the Operate Handle LED will turn OFF and the Tape in Use LED will blink while the drive moves the tape to BOT (Beginning of Tape). When the tape is at BOT, the Tape in Use LED will turn ON steady. Additionally, one of the compression density LEDs on the Left Indicator Panel may be illuminated or blinking. The tape is now ready for use. Data Protection Caution The Write-Protect switch on the data cartridge can be moved while the cartridge is loaded into the drive. The drive will turn on the Write-Protect LED immediately. However, if the drive is writing to the tape, write protect does not take effect until the write operation completes. Before loading the data cartridge, if you move the Write-Protect switch to the left, the tape is write-protected; the Write Protected LED (orange) is ON and data cannot be written to, or erased from, the tape. Before loading the data cartridge, if you move the Write-Protect switch to the right, the tape is write-enabled and data can be written to, or erased from, the tape (if it is not software write-protected). After loading the data cartridge and during operation, if you move the Write-Protect switch from the write-protected position (to the left) to the write-enabled position (to the right), the tape becomes write-enabled after a variable amount of time (seconds). After loading the data cartridge and during operation, if you move the Write-Protect switch from the write-enabled position (to the right) to the write-protected position (to the left), the tape becomes write-protected after a variable amount of time (seconds). Tape in Use Whenever the ...
Este manual também é adequado para os modelos :Equipamento de rede - 4000 (826.08 kb)