Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Press the button to step from one mode to the next. 1 2 Spd FDxAct 1 2 Mode LED View Spd mode: off = 10 Mbpsflash = 100 Mbpson = 1000 MbpsLink Mode Mode LED View button and indicator LEDs Mode LED (one per port) ¦ If the Activity (Act) indicator LED is lit, each Mode LED displays activity information for the associated port—it flickers as network traffic is received and transmitted through the port. ¦ If the Full Duplex (FDx) indicator LED is lit, the Mode LEDs light for those ports that are operating in full duplex. ¦ If the Speed (Spd) indicator LED is lit, the Mode LEDs behave as follows to indicate the connection speed for the port: • Off = 10 Mbps • Flashing = 100 Mbps (the flashing behavior is an on/off cycle once every 0.5 seconds, approximately) • On = 1000 Mbps Introducing the HP Procurve Switch 6108 1-5 Introducing the HP Procurve Switch 6108 Introducing the HP ProcurveSwitch 6108 Front of the Switch Console Port This port is used to connect a console to the Switch 6108 by using the serial cable supplied with the switch. This connection is described under “Connect a Console to the Switch” in chapter 2, “Installing the Switch”. The console can be a PC or workstation running a VT-100 terminal emulator, or a VT-100 terminal. Reset Button This button is used to reset the switch while it is powered on. This action clears any temporary error conditions that may have occurred and executes the switch self test. Clear Button This button is used for these purposes: ¦ Deleting Passwords - When pressed by itself for at least one second, the button deletes any switch console access passwords that you may have configured. Use this feature if you have misplaced the password and need console access. This button is provided for your convenience, but its presence means that if you are concerned with the security of the switch configuration and operation, you should make sure the switch is installed in a secure location, such as a locked wiring closet. ¦ Restoring Factory Default Configuration -When pressed with the Reset button in a specific pattern, any configuration changes you may have made through the switch console, the web browser interface, and SNMP management are removed, and the factory default configuration is restored to the switch. For the specific method to restore the factory default configuration, see “Restoring the Factory Default Configuration” in chapter 4, “Troubleshooting” of this manual. 1-6 Introducing the HP Procurve Switch 6108 Back of the Switch Back of the Switch AC power connector Cooling vent - make sure this is not obstructed for proper switch operation Power Connector The Switch 6108 does not have a power switch; it is powered on when connected to an active AC power source. The switch automatically adjusts to any voltage between 100--240 volts and either 50 or 60 Hz. There are no voltage range settings required. Introducing the HP Procurve Switch 6108 1-7 Introducing the HP Procurve Switch 6108 Switch Features Introducing the HP ProcurveSwitch 6108 Switch Features The features of the Switch 6108 include: ¦ six auto-sensing 10/100/1000Base-T RJ-45 ports. ¦ two dual-personality ports—either the auto sensing 10/100/1000Base-T RJ-45 or the mini-GBIC can be used for each port. ¦ plug-and-play networking—all ports are enabled—just connect the network cables to active network devices and your switched network is operational. ¦ IEEE 802.3ab “Auto MDI/MDI-X” on all twisted-pair ports, meaning that all connections can be made using straight-through twisted-pair cables. Cross-over cables are not required, although they will also work. Complying with the IEEE 802.3ab standard, the pin operation of each port is automatically adjusted for the attached device: if the switch detects that another switch or hub is connected to the port, it configures the port as MDI; if the switch detects that an end-node device is connected to the port, it configures the port as MDI-X. ¦ automatic learning of the network addresses in each switch’s 8000address forwarding table, (with configurable address aging value). ¦ automatically negotiated full-duplex operation for the 10/100/1000 RJ-45 ports when connected to other auto-negotiating devices—the mini-GBIC ports always operate at full duplex. ¦ easy management of the switches through several available interfaces: • console interface—a full featured, easy to use, VT-100 terminal interface that is especially good for out-of-band switch management or for Telnet access to the switch. • web browser interface—an easy to use built-in graphical interface that can be accessed from common web browsers. • HP TopTools for Hubs & Switches—an SNMP-based, graphical network management tool that you can use to manage your entire network. This product is included with your new switch. ¦ support for the Spanning Tree Protocol to eliminate network loops ¦ support for up to 30 IEEE 802.1Q-compliant VLANs so you can divide the attached end nodes into logical groupings that fit your busine...