Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
For instructions on installing and verifying the Windows network driver, refer to “Install the Network Card” on this page. The following seven easy steps are provided in this guide for installing your Model PA301 Network Card: 1. Verify Package Contents 2. Install the Network Card 3. Connect the Telephone Cables 4. Install the Network Driver 5. Install the Model PA301 Software 6. Access the Internet 7. Access the Network Printers As a final step, be sure to register your NETGEAR™ product at Verify Package Contents Unpack the package contents and verify that you have the following: Model PA301 Network Card Installation guide Resource CD Telephone cable (10 ft) 9551FA Verify PC Requirements The instructions given in this guide are for using the NETGEAR Model PA301 Network Card in a PC that has a Microsoft® Windows 95 operating system. Model PA310 Network Card Installation Guide Install the Network Card Install the Network Card Note: Touch a grounded metal object to free yourself of static electricity before you handle the network card. Network card Back plate removed 7983FB 1. Turn the power off and unplug the power cord from your computer. 2. Remove the PC cover. 3. Choose an available PCI slot (PCI slots are the shorter slots) and remove the corresponding back plate from the PC chassis. 4. Insert the network card into the PCI slot and fasten the card to the computer chassis by tightening the screw that is on the PC. Note: To avoid damaging any components on the network card, handle it by the edges, using your thumbs to push it securely into the PCI slot. Make sure the network card is fully inserted into the slot to prevent the PC operating system from experiencing problems. 5. Replace the PC cover and reconnect the power cord to the PC. Model PA310 Network Card Installation Guide Connect the Telephone Cables Connect the Telephone Cables Phone line behind the wall PC with network card installed PC with network card installed Printer (optional) RJ-11 connectors Telephone 9552FA Using the telephone cable provided in the NETGEAR package, connect one end of the telephone cable to the port labeled “TO WALL” on the network card and the other end of the cable to an available wall jack, as illustrated above. Using the cable shipped with your telephone or modem, connect that cable to the port labeled “TO PHONE” on the network card. If you are using an external analog modem to connect to the Internet, refer to the following illustration that shows the connections for the wall jack, Model PA301 Network card, external modem, and phone. Note that the captions on the modem Card, network card, and modem direct you to the outlets where you connect the cables. Wall jack PC Serial cable External modem Phone 9571FB Telephone wire Model PA310 Network Card Installation Guide The illustration below depicts the configuration with an internal modem and shows a closeup of the connections for the wall jack, modem card, Model PA301 Network Card, and phone. Note that the caption on the modem card and network card direct you to the outlets where you connect the cable from the wall jack and the cable that connects to the phone. Note: For optimal performance, the Model PA301 Network Card should be plugged directly into a wall jack, and the modem should be plugged directly into the network card. Wall jack PC with Model PA301 Network Card and internal modem To phone To line Phone 9572FA Modem Model PA301 Network Card Model PA310 Network Card Installation Guide Install the Network Driver Install the Network Driver This guide provides instructions for installing the Windows Network Driver. The steps given are for users of Windows 95. However, because all versions of Windows 95 might not respond the same, windows that are different from those shown in these instructions might open but prompt you for the same information, or windows might open in a different order than shown in these instructions. If you are using Windows 98, read these instructions thoroughly for an overview of the steps that are necessary for the installation of the software driver. Follow the instructions given by the Windows 98 Installation Wizard to install the driver. Note:You must install the network card before installing the network driver. You need to have the Windows 95 or Windows 98 CD and the NETGEAR Phoneline10X Resource CD ready to use in the installation process. If you have not yet named your PC and your network, before you proceed with the installation steps, decide on a name for your network and for each PC. You will be using these names in section 5, “Install the PA301 Software.” Note: If the “Insert CD” window opens and the “Please insert the CD labeled Windows”...message appears at any time during the installation process, insert the Windows CD and click on OK. Then proceed with the following steps. 1. Turn on the power to the computer and start Windows. The new hardware is found and the driver is automatically loaded. 2. New Hardware Foun...