Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
This value can range from 1 to 1440 minutes. The default period is 30 minutes. Shorter durations ensure that control points have current device status at the expense of additional network traffic. Longer durations can compromise the freshness of the device status, but can significantly reduce network traffic. Advertisement Time to Live. The time to live for the advertisement is measured in hops (steps) for each UPnP packet sent. The time to live hop count is the number of steps a broadcast packet is allowed to propagate for each UPnP advertisement before it disappears. The number of hops can range from 1 to 255. The default value for the advertisement time to live is 4 hops, which should be fine for most home networks. If you notice that some devices are not being updated or reached correctly, then it might be necessary to increase this value. UPnP Portmap Table. The UPnP Portmap Table displays the IP address of each UPnP device that is currently accessing the WiFi DSL modem router and which ports (internal and external) that device has opened. The UPnP Portmap Table also displays what type of port is open and whether that port is still active for each IP address. 3.Click Apply to save your settings. You can use this feature to set up an IPv6 Internet connection type if NETGEAR genie does not detect it automatically. 1.Select ADVANCED > Advanced Setup > IPv6 to display the following screen: 2.Select the IPv6 connection type from the list. Your Internet service provider (ISP) can provide this information. •If your ISP did not provide details, you can select IPv6 Tunnel. •If you are not sure, select Auto Detect so that the WiFi DSL modem router detects the IPv6 type that is in use. •If your Internet connection does not use PPPoE, DHCP, or fixed, but is IPv6, then select IPv6 auto config. 3.Click Apply so that your changes take effect. Traffic Meter Traffic metering allows you to monitor the volume of Internet traffic passing through your WiFi DSL modem router’s Internet port. With the traffic meter utility, you can set limits for traffic volume, set a monthly limit, and get a live update of traffic usage. 1.Click ADVANCED > Advanced Setup > Traffic Meter to display the following screen: 2.To enable the traffic meter, select the Enable Traffic Meter check box. 3.If you would like to record and restrict the volume of Internet traffic, select the Traffic volume control by radio button. You can select one of the following options for controlling the traffic volume: •No Limit. No restriction is applied when the traffic limit is reached. •Download only. The restriction is applied to incoming traffic only. •Both Directions. The restriction is applied to both incoming and outgoing traffic. 4.You can limit the amount of data traffic allowed per month by specifying how many Mbytes per month are allowed or by specifying how many hours of traffic are allowed. 5.Set the traffic counter to begin at a specific time and date. 6.Set up traffic control to issue a warning message before the monthly limit of Mbytes or hours is reached. You can select one of the following to occur when the limit is attained: •The Internet LED blinks green or red. •The Internet connection is disconnected and disabled. 7.Set up Internet traffic statistics to monitor the data traffic. 8.Click the Traffic Status button to get a current update of Internet traffic status on your WiFi DSL modem router. 9.Click Apply to save your settings. USB Settings For added security, the WiFi DSL modem router can be set up to share only approved USB devices. See Specify Approved USB Devices on page 70 for the procedure. 10. Troubleshooting Diagnose and solve problems This chapter provides information to help you diagnose and solve problems you might have with your WiFi DSL modem router. If you do not find the solution here, check the NETGEAR support site at for product and contact information. This chapter contains the following sections: •Quick Tips •Troubleshoot with the LEDs •Cannot Log In to the Router •Cannot Access the Internet •Changes Not Saved •Incorrect Date or Time •Wireless Connectivity •Restore the Factory Settings and Password •Troubleshoot Your Network Using the Ping Utility This section describes tips for troubleshooting some common problems. Sequence to Restart Your Network Be sure to restart your network in this sequence: 1.Turn off and unplug the modem. 2.Turn off the WiFi DSL modem router and computers. 3.Plug in the modem and turn it on. Wait 2 minutes. 4.Turn on the WiFi DSL modem router and wait 2 minutes. 5.Turn on the computers. Check Ethernet Cable Connections Make sure that the Ethernet cables are securely plugged in. •The Internet status LED on the WiFi DSL modem router is lit if the Ethernet cable connecting the WiFi DSL modem router and the modem is plugged in securely and the modem and WiFi DSL modem router are turned on. •For each powered-on computer connected to the WiFi DSL mod...