Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
They currently use analog cellular or standard phone lines to connect in circuit- switched mode for data transfer. Analog cellular phone service is being discontinued. The combination of the Host RJ-11 IP Gateway, RJ-11 IP Gateway, and the AirLink Raven-E enables remote connectivity between host applications and these remote devices over cellular packet data networks. The RJ-11 IP Gateway provides the bridge between a device requiring an RJ-11 interface and the Raven-E, with its Ethernet interface. The Host RJ-11 IP Gateway can provide Ethernet-based Internet connectivity to a Legacy Host system with only RJ-11 ports. FIGURE 1. Host RJ-11 Ethernet Connectivity for a Legacy Host FIGURE 2. Host RJ-11 Gateway with an AirLink Raven-E and a Modem Router Host RJ-11 IP Gateway Features •One RJ-11 phone port The phone port is a phone line designed to function just like standard wall-jack analog phone line. It is designed primarily to connect dial-up devices, with internal modems, to the RJ-11 IP Gateway, which then routes data from the devices over the network. The RJ-11 IP Gateway and Host RJ-11 IP Gateway mimics the phone company, answering incoming calls and routing them to an internal modem attached to the phone port, or generating calls from an internal modem to an attached device. Caution: The Host RJ-11 IP Gateway's RJ-11 phone port should never be connected into the Public Switched Telephone Network (PSTN). This device is designed to emulate the PSTN for other devices. The Host RJ-11 IP Gateway may sustain damage not covered by warranty if it is connected to the Public Switched Telephone Network. •One RJ-45 auto-sensing 10base-T Ethernet port The Ethernet port is designed to be connected to either an AirLink modem with an Ethernet port such as the Raven-E or Raven X or any Ethernet-based network. With the modem connected to the cellular network, the communication from the device connected to the RJ-11 port can be routed to the Internet and your remote host. •One power connector The Host RJ-11 IP Gateway uses a AC power adapter with an optional DC adapter available. •Status LEDs The Host RJ-11 IP Gateway status LEDs give clear and concise information about the operation of the ports. CHAPTER 2Installation Configuring the Host RJ-11 IP Gateway to work with your network or Raven-E and your RJ-11 equipped device is easy. This chapter covers a basic configuration. Caution: The Host RJ-11 IP Gateway’s RJ-11 port (labeled “Phone”) should not be connected into the Public Switched Telephone Network. This port is the emulation for a Phone that you would have been using with your device. The RJ-11 IP Gateway will sustain damage not covered by warranty if it is connected to the Public Switched Telephone Network. Before You Start Caution: If the Host RJ-11 IP Gateway and Raven-E (as applicable) are going to be on a hub which is connected to a local network, you will need to be sure the addresses you select are not used by any other device on the network. Consult with your network administrator if you are unsure. Software Required •Wireless Ace - Graphical interface for configuring your Raven-E. Wireless Ace is located on Host RJ-11 IP Gateway CD or you can download Wireless Ace from the AirLink website: http:/ /A default installation of this utility is assumed later in these directions. If you will not be connecting the Host RJ-11 IP Gateway to a Raven-E, you will not need Wireless Ace. •Host RJ-11 IP Gateway Port Utility - Utility to establish an initial IP address for your Host RJ-11 IP Gateway. The port utility is located on the Host RJ-11 IP Gateway CD or you can download it from the AirLink website: A default installation of this utility is assumed later in these directions. If you will be connecting the Host RJ-11 IP Gateway to a Raven-E, you will not need the port utility. If you can use the default IP address of the Host RJ-11 IP Gateway for the initial configuration, you, also, will not need the port utility. Hardware Required •Ethernet Cable - A cross-over or straight through Ethernet cable. If you will be connecting the Host RJ-11 IP Gateway to a Raven-E, you will need a cross-over Ethernet cable to configure your Raven-E unless your computer’s Ethernet port is auto-sensing. The Host RJ-11 IP Gateway has an auto-sensing Ethernet port, you can use either a cross-over cable or a straight-through Ethernet cable to connect the Host RJ-11 IP Gateway to the Raven-E or your computer. •Power supplies and a power source - You will need a power supply and power source for both the Host RJ-11 IP Gateway and the Raven-E (as applicable). •PC or Laptop - To configure both the Host RJ-11 IP Gateway and the modem (as applicable), you will need a computer with Internet Access, other than the cellular account, and an available Ethernet port. Cellular Account Required •Cellular Account - If you will be connecting the Host RJ-11 IP G...
Este manual também é adequado para os modelos :Equipamento de rede - RJ-11 (1.75 mb)
Equipamento de rede - RJ-11 (1.75 mb)
Equipamento de rede - RJ-11 (1.75 mb)
Equipamento de rede - RJ-11 (1.75 mb)