The PC Card has the ability automatic sensing and operating on either speed without manual reconfiguration. Please refer to Software Installation on how to install network drivers using menu driven installation utility. Inserting the Dual Speeds Fast Ethernet PC Card 1. Hold the PC Card with wide connector toward the slot and the brand label facing upward. 2. Insert the PC Card and push it firmly into the bottom. (Please see the figure on the next page for reference) Removing the Dual Speed Fast Ethernet PC Card It’s quite different for various computer mechanical designs. Please refer to the PC Card removal instruction in the document for your notebook computer. Connecting and Removing the Cable of Media Coupler to the PC Card Grasp the PC Card 15-pins connector at the end of the media coupler with the pointing triangle facing upward. Gently insert it into the mating connector on the PC Card until it clicks in place at both sides. Attention should be paid when removing the 15-pins connector. Please press the both sides of the connectors before dragging out of the PC Card. Connecting to the Network Connect unshielded twisted pair (UTP) cable to the RJ-45 connector of media coupler before loading any network driver. symbol 108 \f "Monotype Sorts" \s 6.. For operation in the100Mbps (100Base-TX) Ethernet network, a Category 5 unshielded twisted pair(UTP) cable should be used to connect between media coupler and 100Mbps hub or switch. symbol 108 \f "Monotype Sorts" \s 6.. For operation in the 10Mbps (10Base-T) Ethernet network, Category 3, 4 or 5 unshielded twisted pair (UTP) cable could be used to connect between the media coupler and a 10Mbps hub or switch. LED Indicators SOFTWARE INSTALLATION Plug the driver diskette into the floppy drive and set the current drive to the floppy drive. Then run INSTALL to install the real mode drivers such as ODI or NDIS 2.x or Packet Drivers into the target disk. Novell Netware There are two methods to install the Netware client ODI driver, the menu installation and Netware 3.12 or 4.x Client installation. Menu Installation 1.Run INSTALL.EXE from the root directory of driver diskette. 2.Select Netware 3.x and 4.x Workstation” item from menu. 3.If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters to make settings changed 4.Move cursor to focus on the setting you want to make change and press ” to select a fit value. When the configurations are set completely, press on the OK” field to exit the screen and go back to step 3. 5.Installation program starts copying related files from diskette to the destination directory and modifies AUTOEXEC.BAT and NET.CFG under usersymbol 146 \f "Parisian BT" \s 10’}s agreement 6.Now, the installation is completed. Please reboot the computer to make your Netware connection. If you wanted to install the ODI driver by manual, you may follow the instructions list below. 1.Copy the files LE100ODI.COM and NET.CFG from the path \NETWARE and the file LANEN.EXE from the path \ENABLER in the driver diskette into the Netware client directory containing Novell's LSL.COM, IPXODI.COM and NETx.COM files. 2.Using a text editor to edit the NET.CFG for setting the default frame type. In the Netware server the frame type is set to 802.3 for NW3.11 and 802.2 for NW3.12 and NW4.x The frame type must be set to the same with the server or the client couldnsymbol 146 \f "Parisian BT" \s 10’}t login to the server. 3.Follow Novell's instructions on using ODI programs. You can substitute the LE100ODI.COM whenever a reference is made to the Hardware Specific Module. 4.A typical ODI workstation startup batch file includes: >LANEN /IRQ=dd /IOP=xxx Card Enabler >LSL ;Link Support Layer Module provided by Novell >LE100ODI ;Hardware Specific Module >IPXODI ;IPX Protocol Stack Module provided by Novell >NETx ;Shell Support Module provided by Novell >LOGIN Novell Client Installation 1.Run the NetWare Client Install V1.21 -Get the 4 Client disks from the network administrator, or -Run the \NWCLIENT\INSTALL.EXE in a previous Installation 2.A message appears on the screen asking you whether or not you want the program to perform modifications on your AUTOEXEC.BAT and CONFIG.SYS files. 3.Answer "Yes". The program then modifies your AUTOEXEC.BAT and CONFIG.SYS files accordingly and creates backup copies. 4.The following message appears: -Install support for MS Windows? (Y/N): 5.Answer accordingly and provide a path if necessary. 6.The program displays the following: -Configure your workstation for backup by a NetWare server running software such as BACKUP? (Y/N): 7.Answer accordingly and provide a path if necessary. 8.Select a driver for your network board. 9.From the driver list, select Other Drivers. 10.Go to the Insert the Driver Disk dialog box and specify the path where the ODI driver and INS files reside. For example: C:\ODI.DOS. 11.Press Enter and select the target ODI driver. 12.Specify the driver'...
