Log: Slow Blinking (Blinking 1 time per second) Synchronized with an SNR margin Green greater than the user defined SNR Margin Alarm Threshold and the pulse attenuation is greater than the user defined Loop Attenuation Alarm Threshold Solid Yellow Synchronized with an SNR margin greater than 0 dB but less than the user defined SNR Margin Alarm Threshold . Slow Blinking Synchronized with an SNR margin greater than 0 dB but less than the Yellow user defined SNR Margin Alarm Threshold and the pulse att
3 dB. LED STATUS DSX EQ SPLITTING JACKS DSX MONITOR JACKS COMPLIANCE POWERING MODE utCode Input Output Power Code (PC) F C Telecommunication Code (TC) – X Installation Code (IC) A – 1. DSX-1 Line Build Out 0-133 Feet 0-133 Feet Provisioning Options Option Settings Default Settings Red Loop 1/ Loop 2 synchronization not achieved, in sync with errors, or SNR margin < 3 dB. 133-266 Feet 266-399 Feet DSX Green DSX-1 signal present and no errors currently detected. 399-533 Feet Red In framed mode,
1. Connect the DB-9 (male) connector of your serial cable to the console port on the rear panel of the unit. 2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal emulation software). 3. Open a VT100 terminal session to the Total Access 234 using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press
1 2. INSTALLATION.................................................................. 2 3. OPERATION ........................................................................ 3 4. HDSL SYSTEM TESTING.................................................. 4 5. SCU CONTROL PORT OPERATION (HDSL) ................. 5 6. HDSL DEPLOYMENT GUIDELINES ............................. 17 7. MAINTENANCE ............................................................... 17 8. PRODUCT SPECIFICATIONS .......................
It supports HTTP, HTTPS, DHCP, Syslog, SNMP, SMTP and SNTP protocols. An internal clock allows to timestamp syslogmessages, e-mails and internal logs. High Security ePowerSwitch with IP device andenvironmental monitoring Zone de Texte: ePowerSwitch ..Multiple concurrent usersAllows multiple concurrent user access. Each user has access to control his designated power outlets. ..DHCP clientThe DHCP option enables to reduce the configuration management. ..Scheduler for Time-Controlled ApplicationsT
RJ-45 CONFIGURATION Set the switches located on either side of the adapter to the desired network settings. Use the same setting for both switches. 'warranty ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at USA and Canadian customer Faxback: (877) 457-5007, Document 414. For service, CAPS requests, or further information, contact one of the following numbers: ADTR
INSTALLATION .......................................................3 3. CONFIGURATION ...................................................4 4. OPERATIONAL DESCRIPTION .............................5 5. NORMAL OPERATION ...........................................6 6. PROTECT OPERATION...........................................6 7. PROTECTION SWITCH ...........................................8 8. SWITCHBACK ........................................................10 9. AUTO-PROTECT OPERATION .......
It includes also many monitoring functionalities and supports SNTP and SMTP protocol. ePowerSwitch 8XM Master Technology House -Trafalgar Way Bar Hil -Cambridge -UK CB3 8SQ Tel:+44 (0)1954 780044 -Fax:+44 (0)1954 780081 High security ePowerSwitch supports https (SSL) protocol Zone de Texte: ePowerSwitch ..Advanced SecurityFor your security, account access and data transfer are encrypted with SSL Technology. ..Multiple concurrent usersAllows multiple concurrent user access to the Master and all S
The NetVanta 1355 PWR units are fully compliant with the power delivery options called out in the IEEE 802.3af Power over Ethernet specification. By default, the PoE interfaces discover and provide power to IEEE compliant PDs. To disable power detection and supply, use the power inline never command in the CLI. To disable power detection and supply from the GUI, select the Ports page. Then select a single port from the list (e.g., eth 0/1). This will bring up the port detail page for eth 0/1. On
two slots, 19/20 or 21/22, on the Total Access 3010. The odd cable carries the IMA RX pairs, and the even cable carries the IMA TX pairs. Termination of the cable amphenols are customer designated. The converter cable group is comprised of two separately sheathed cable bundles. The Table below charts the port-slot-function-color code for each OCTAL IMA cable. Each bundle has four 50-pin female amphenol connectors on the Total Access 3010 end, and three 50-pin male amphenols on the MDF end, assig
