Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Hold the sander upside down with its top against a flat, stable surface. 3. Place the sandpaper over the base and align the holes in the paper with holes in the base (Figure 1). Figure 1. Sandpaper and base holes aligned. Model D3736 Palm Finishing Sander Tip: Try using the sandpaper that came with your sander as a template for cutting holes in new 1.4 sheets to match those on the bottom of the sander—so the dust bag can collect dust particles. Use a paper punch to cut the holes; or mark the holes, score them with a sharp knife, and cut them out. Attaching Dust Bag Using the dust bag will help keep your work area clean and reduce dust particle emission. To install the dust bag, do these steps: 1. Insert the dust bag spout into the dust port and make sure it fits snugly. 2. When the dust bag is half full, remove the dust bag from the sander and empty it into a trash receptacle by gently tapping on the side of the bag. Always wear a respirator or dust mask and safety glasses when emptying the dust bag. Using the Sander Determine the appropriate grit size for your project and sand the work evenly in the same direction as the grain of the wood. Always keep the sander moving so the finish of your work stays consistent. If the sander stays in one place too long, then it may produce a depression in the wood that will compromise your finish. Sanding across the grain of the wood may be necessary in some cases to remove rough defects. This should be done with caution, however, because it can produce cross-grain scratching that will require further sanding to remove. Electrical shock hazard! Only use sander for dry sanding. Never use sander for wet sanding! Change sheets as soon as the grit becomes dull. And, never apply excessive force while sanding. Your sander and paper will last longer if you let them do the work. -7 Model D3736 Palm Finishing Sander -8- MAINTENANCE Your Model D3736 Palm Finishing Sander will give you years of trouble free service if you keep it clean and free of built-up dust or grime. Ensure that no air passages get blocked. If they do, blow them out with compressed air. CAUTION: Unprotected eyes can be injured by dust particles propelled by compressed air. ALWAYS wear safety glasses and a dust mask when cleaning the sander with compressed air. Plastic parts can easily be cleaned with a damp cloth, but never use water to clean any electrical parts. Solvents should also be avoided on plastic because of the possibility of damage. If possible, use a scraper to remove glue or sap from your work; these elements may hinder the effectiveness of the abrasive sheets and cause unnecessary build-up of grime on the sander. Keeping Tool Clean Regular periodic maintenance on your Model D3736 Palm Finishing Sander will ensure its optimum performance. Make a habit of inspecting your sander each time you use it. Check for the following conditions and repair or replace when necessary: • Loose fasteners. • Worn switch. • Worn or damaged cords and plugs. • Worn or damaged sanding pad. • Any other condition that could hamper the safe operation of this tool. General Model D3736 Palm Finishing Sander D3736 PARTS BREAKDOWN .............................................................................................................................. .............................................................................. -9 Model D3736 Palm Finishing Sander D3736 PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 XD3736001 TOP HOUSING COVER 2 XD3736002 LEFT HOUSING 3 XD3736003 RIGHT HOUSING 4 XD3736004 STATOR 5 XD3736005 ROTOR 6 XP609 BALL BEARING 609 7 XP627 BALL BEARING 627 8 XD3736008 ALUMINUM FAN 9 XP6000 BALL BEARING 6000ZZ 10 XD3736010 PARTITION 11 XD3736011 SPACER 12 XD3736012 BASE PLATE 13 XD3736013 FOAM PLATE 14 XD3736014 TOGGLE BAR 15 XPSW07 SWITCH 16 XD3736016 POWER CORD GUARD 17 XD3736017 POWER CORD 18AWG X 3C 18 XD3736018 DUST BAG 19 XD3736019 DUST BAG BRACKET 20 XD3736020 BRUSH BOX 21 XD3736021 CARBON BRUSH 22 XD3736022 BRUSH HOLDER 23 XPHTEK39M TAP SCREW M4 X 12 24 XPHTEK6M TAP SCREW M4 X 16 25 XPHTEK31M TAP SCREW M4 X 14 26 XPHTEK39M TAP SCREW M4 X 12 27 XPHTEK39M TAP SCREW M4 X 12 28 XD3736028 BRACKET 29 XD3736029 MODEL NUMBER LABEL 30 XD3736030 DUST WARNING LABEL 33 XD3736033 RUBBER POLE 34 XPHTEK11M TAP SCREW M3 X 8 35 XD3736035 PRESS BOARD 36 XD3736036 120 GRIT SANDPAPER 4-1/4" X 4-1/2" -10 Model D3736 Palm Finishing Sander Troubleshooting Symptom Possible Cause Possible Solution Reduced amount of material removed 1. Sandpaper clogged with paint or glue. 1. Replace sandpaper. by sander, quality of finish decreases, sander slides easily across workpiece. 2. Sandpaper grit dull. 2. Replace sandpaper Sander generates 1. Dust bag full. 1. Empty dust bag. excessive dust 2. Holes on sandpaper not 2. Use abrasive paper with particles. aligned with holes in sander base. 3. Sandpaper lacks holes. 4. Holes in sander base clogged. pre-punched holes that match holes on base. 3. Cut or punch holes in...