Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
When the job is applying to the work; swirl marks will result in completed, release switch, and gently lift the either case. In general, higher speeds and tool from the work surface at the same time. moderate pressure will give the best results. If POLISHING: for most polishing, the soft faster removal is desired, DO NOT INCREASE backing pad will give the best results. The PRESSURE ON THE TOOL; use a coarser random orbit sander may be fitted with a -8 BM 2609932240 7/02 7/25/02 2:37 PM Page 9 foam buffing pad or polishing bonnet to polish It is important to note that the orbit speed of or remove scratches from painted or finished the random orbit sander is not the same as surfaces, plastics, and even glass. The tool is the RPM of a standard right-angle polisher. operated in much the same way as when The random orbit action is much like a sanding, but the following points should be powerful hand polishing action, and therefore observed; does not have the high speeds at the edge of the pad which can burn the work surface. For Apply the compound to the surface, and use this reason, it is possible to select a higher the sponge applicator pad with light pressure OPM for the random orbit sander than the and a circular motion to remove scratches recommended RPM for a standard polisher. and restore weathered finishes. Use only as Practice on a hidden area or test surface until much compound as necessary, and clean the you have determined the tool is suitable for sponge frequently during use. your polishing application. When initial polishing is completed, wipe away Clean the buffing pad and polishing bonnet any excess compound with a soft towel, and with mild detergents and warm water. DO then polish the surface to its final finish with NOT use solvents. the polishing bonnet. Use smooth overlapping strokes for best results. Maintenance Service should be replaced at Bosch Factory Preventive maintenance Service Center or Authorized Bosch Service performed by unauthorized Station. Bearings which become noisy (due personnel may result in misplacing of to heavy load or very abrasive material cut- internal wires and components which ting) should be replaced at once to avoid could cause serious hazard. We overheating or motor failure. recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. Cleaning ! WARNING ! WARNING To avoid accidents always TOOL LUBRICATION disconnect the tool from Your Bosch tool has been properly the power supply before cleaning or lubricated and is ready to use. It is performing any maintenance. The tool may recommended that tools with gears be be cleaned most effectively with regreased with a special gear lubricant at compressed dry air. Always wear safety every brush change. goggles when cleaning tools withCARBON BRUSHES compressed air. The brushes and commutator in your tool Ventilation openings and switch levers must have been engineered for many hours of be kept clean and free of foreign matter. Do dependable service. To maintain peak not attempt to clean by inserting pointed efficiency of the motor, we recommend objects through openings. every two to six months the brushes be examined. Only genuine Bosch replacement ! CAUTION Certain cleaning agents and solvents damage plastic should be used. parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, brushes specially designed for your tool BEARINGS ammonia and household detergents that After about 300-400 hours of operation, or at contain ammonia. every second brush change, the bearings -9 BM 2609932240 7/02 7/25/02 2:37 PM Page 10 Accessories ! WARNING If an extension cord is necessary, a cord with adequate size conductors that is capable of carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles. NOTE: The smaller the gauge number, the heavier the cord. * Allen wrench 5mm * Dust canister * Auxiliary Handle * Soft backing pad ** Extra soft backing pad ** Hard backing pad RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS Tool’s Ampere Cord Size in A.W.G. Wire Sizes in mm2 Rating Cord Length in Feet Cord Length in Meters 25 50 100 150 15 30 60 120 3-6 18 16 16 14 .75 .75 1.5 2.5 6-8 18 16 14 12 .75 1.0 2.5 4.0 8-10 18 16 14 12 .75 1.0 2.5 4.0 10-12 16 16 14 12 1.0 2.5 4.0 — 12-16 14 12 — — — — — — ** Vacuum hose adapter (tool end) ** Vacuum hose adapter (canister end) ** Vacuum hose (*= standard equipment) (**= optional accessories) -10 BM 2609932240 7/02 7/25/02 2:37 PM Page 11 Regles de Securite Generales AVERTISSEMENT! Vous devez lire et comprendre toutes les instructions. Lenon-respect, meme partiel, des instructions ci-apres entraine un risque de choc eletrique, d'incendie et/ou de blessures graves. CONSERVEZ CES INSTRUCTIONS Aire de travail Veillez a ce que l'aire de t...