Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Accessories that may be suitable for one tool, may become hazardous when used on another tool. Service Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. For example: internal wires may be misplaced or pinched, safety guard return springs may be improperly mounted. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia, etc. may damage plastic parts. Belt Sander Safety Rules Hold tool by insulated gripping surfaces when performing a operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. If your tool is equipped with a dust bag, empty it frequently and after completion of sanding. Be extremely careful of dust disposal, materials in fine particle form may be explosive. Do not throw sanding dust on an open fire. Spontaneous combustion, may in time, result from mixture of oil or water with dust particles. Use special precautions when sanding chemically pressure treated lumber, paint that may be lead based, or any other materials that may contain carcinogens. A suitable breathing respirator and protective clothing must be worn by all persons entering the work area. Work area should be sealed by plastic sheeting and persons not protected should be kept out until work area is thoroughly cleaned. -3 Do not wet sand with this sander. Liquids entering the motor housing is an electrical shock hazard. Never leave the trigger locked “ON”. Before plugging the tool in, check that the trigger lock is “OFF”. Accidental start-ups could cause injury. Unplug the sander before changing accessories. Accidental start-ups may occur if sander is plugged in while changing an accessory. Keep your fingers and clothing away from the belt. They could get cut or wedged between the pulley, belt and motor housing. Properly adjust tracking of belt to avoid it overhanging the housing. A running belt overhanging its housing can cause severe lacerations. Be aware of the location and setting of the Switch "Lock-ON" Button. If the switch is locked "ON", be ready for emergency situations to switch it "OFF", by first pulling the trigger then immediately releasing it emergency situations. Always follow without pressing the "Lock-ON" button. directions included with the accessory. Use sanding fence, stop or guide when sanding Keep the cord to the side away from short or small workpieces. pulleys. The cord can be dragged into belt housing and become entangled with the ! WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction pulleys. Clamp or secure workpiece when activities contains chemicals known to sanding. Clamping the workpiece prevents cause cancer, birth defects or other it from being ejected from under the sander reproductive harm. Some examples of and leaves both hands to control the tool. these chemicals are: Clamp or secure sander if it is inverted • Lead from lead-based paints, and bench mounted for use as a table sander. Always use edge stop or guide • Crystalline silica from bricks and cement when sanding short or small workpieces. and other masonry products, and Fingers or clothing can be dragged into • Arsenic and chromium from chemically- pulley and housing area. treated lumber. Portable belt sanders are not intended to be Your risk from these exposures varies, permanently mounted as a bench or table depending on how often you do this type of sander. There are accessories available work. To reduce your exposure to these which can convert certain portable belt chemicals: work in a well ventilated area, sanders for occasional stationary use. If such and work with approved safety equipment, accessories are used always clamp or secure such as those dust masks that are specially sander when inverted and bench mounted designed to filter out microscopic particles. for use as a table sander. Be aware of switch location and know how to shut off the tool in -4 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Designation/Explanation V Volts Voltage (potential) A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power kg Kilograms Weight min Minutes Time s Seconds Time Diameter Size of drill bits, grinding wheels, etc. n0 No load speed Rotational speed, at no load .../min Revolutions or reciprocation per minute Revolutions, strokes, surface speed, orbits etc. per minute 0 Off position Zero speed, zero torque... 1, 2, 3, ... I, II, III, Selector ...