Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Belt Sander FIG. 1 VENTILATION OPENINGS SANDING BELT WING KNOB BELT TENSION RELEASE LEVER PLATEN PROTECTOR VARIABLE SPEED DIAL 1275DVS &1276DVS ADJUSTABLE TOP HANDLE “LOCK-ON” BUTTON DUST BAG TRIGGER SWITCH STATIC CLIP Model number 1275DVS 1276DVS 1276D Voltage rating 120 V 50 - 60Hz 120 V 50 - 60Hz 120 V 50 - 60Hz Amperage rating 10.5 A 10.5 A 10.5 A No load speed n0 1,150-1,550/min n0 1,150-1,550/min n0 1,550/min Belt size 3" x 24" 4" x 24" 4" x 24" -6 BM 2610967913 9/03 9/26/03 4:56 PM Page 7 Assembly BELT INSTALLATION ! WARNING To prevent personal injury, always disconnect the plug from the power source before removing or installing the belt. Your belt sander will accept non woven or polishing belts up to 8mm (5/16") thick, but it is necessary to adjust the dust port flap to allow clearance for the thicker belt. To adjust flap, remove screw and pull position knob free of the tool. Lower dust port flap slightly, and reinsert the position knob with the locating tab facing forward as shown to hold flap in the lowered position. Reinsert screw and tighten position knob in place. To raise flap back to its normal position for standard sanding belts, reverse this procedure. Place sander upside down, and pull belt tension release lever towards rear of tool to release the belt. Pull the old belt free of the pulleys through the open side of the sander. To install new belt, leave lever fully released and place the new belt in position over the pulleys and platen protector. If the belt has a direction of rotation arrow marked on its inside surface, be sure to face the belt in that direction. With the belt properly positioned, push lever back into its recess to apply proper tension to the belt. POSITION KNOB SCREW Normal position for standard belts LOCATING TAB PORT FLAP Open position for non-woven or polishing belts up to 8mm (5/16") thick. Operating Instructions TRIGGER SWITCH AND “LOCK-ON” BUTTON Your sander can be turned “ON” or “OFF” by squeezing or releasing the trigger. Your sander is also equipped with a “Lock-ON” button located just above the trigger that allows continuous operation without holding the trigger TO LOCK SWITCH ON: squeeze trigger, depress “Lock-ON” button and release trigger. TO UNLOCK THE SWITCH: squeeze trigger and release it without depressing the “Lock- ON” button. ! WARNING If the “Lock-ON” button is continuously being depressed, the trigger cannot be released. VARIABLE SPEED DIAL (1275DVS & 1276DVS) This tool is equipped with a variable speed dial. The belt speed may be controlled by presetting the dial in any one of six positions. Dial setting 3 thru 5 3 thru 5 4 thru 6 3 thru 6 -7 Material/Application Delicate surfaces, veneers, and with sanding frame for light surface finishing. Plastics or other surfaces where belt loading or heat buildup is a problem Solid wood, fast stock removal, paint removal General service, metal sanding, chipboard, coarse sandingon rough surfaces BM 2610967913 9/03 9/26/03 4:56 PM Page 8 TRACKING ADJUSTMENT Turn sander upside down and plug it into the power source. Hold the sander firmly with one hand, engage trigger switch to turn the tool “ON”, and note the tracking of the sanding belt. If the belt runs outward (towards the open side of the sander) turn tracking adjustment knob counter-clockwise. If the belt runs inward, turn the knob clockwise. Adjust the belt in this manner until the edge of the belt runs flush with the outer edge of both pulleys and covers the platen protector. Your sander is now ready for use. In some cases, the belt will require a slight readjustment after it is applied to the work surface, so note the tracking carefully during the first minutes of operation and readjust as required. ADJUSTABLE TOP HANDLE The top handle provided should always be used to guide and balance the tool. Grip the tool by the multi-position top handle, and the rear handle, for safe control and ease of operation. To adjust the top handle, loosen wing knob at least two full turns, position handle and retighten knob firmly. DUST EXTRACTION Proper dust removal will extend abrasive life and produce more consistent results. The integral dust extraction system collects sanding dust in the dust bag assembly. Bag should be emptied when it is no more than half full, and should be replaced when the surface becomes clogged with dust or efficiency will be reduced. To empty or replace bag, pull the bag free of dust port. Open the zipper on the rear of the bag, and empty contents into suitable receptacle. To install bag, firmly push the bag into place on the dust port so that it covers the "O" ring to create a seal and the metal flange on dust TRACKING ADJUSTMENT KNOB bag makes contact with the static clip as shown. The static clip is provided to dissipate static electricity that accumulates in the bag and can cause annoying shock to the user. For added efficiency, a vacuum hose and adaptor (optional accessories) are also available which will allow your sander to be connected...
Este manual também é adequado para os modelos :Máquinas e acabar - 1276D (4.1 mb)
Máquinas e acabar - 1276DVS (4.1 mb)