Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
See Page 26 for complete instruction on rewiring the sander. To attach the motor to the stand: Attach the motor to the stand with (4) M8-1.25 x 20 cap screws, (4) M8 flat washers, (4) M8 lock washers, (4) plastic disc pads and (4) M8-1.25 hex flange nuts (Figure 6). Note–The plastic disc pads should be installed between the motor and the stand. Stand Plastic Disc Pads (One Under Each Corner) Motor Figure 6. Attaching motor to stand. Dust Hood Brackets The two dust hood brackets are identical, but they do not attach to the stand in the same configuration. Figure 7 shows the correct bracket configuration. Dust Hood Brackets Figure 7. Dust hood bracket configuration (Front View). To attach the dust hood brackets to the stand: Attach the dust hood brackets to the stand with (4) M8-1.25 x 40 cap screws, (4) M8 flat washers and (4) M8 lock washers (Figure 8). Figure 8. Attaching dust hood brackets to stand (back-side view). G0518 Drum / Flap Sander -15 Dust Hoods Acrylic Eye ShieldAcrylic Eye Shields To attach the dust hoods to the brackets: Attach the dust hoods to the brackets with (4) M8 1.25 x 40 cap screws, (4) M8 flat washers and (4) M8 lock washers (Figure 9). Figure 9. Attaching one of the dust hoods. To attach the acrylic eye shields to the dust hoods: Loosely attach the acrylic eye shields to the dust hoods with (4) M8-1.25 x 20 cap screws, (4) M8 flat washers and (4) M8 lock washers (Figure 10). Final tighten the cap screws carefully as to not break the acrylic eye shields. Note–Match the correct acrylic eye shield to each dust hood by aligning the mounting holes. Figure 10. Attaching one of the acrylic eye shields. -16-G0518 Drum / Flap Sander Sanding Drum Slide the arbor wrench over the “flat” on the arbor when loosening or tightening the arbor nuts. Figure 11 shows the location of the arbor “flat.” To attach the sanding drum to the arbor: 1. Slide the sanding drum onto the left-side arbor. Note–Make sure the air valve on the sanding drum faces away from the motor. 2. Begin threading the right-hand threaded arbor nut onto the end of the arbor. 3. Using the two arbor wrenches, tighten the arbor nut to secure the sanding drum onto the arbor as shown in Figure 12. 4. Slide the sanding sleeve over the sanding drum as shown in Figure 13. If there is a directional arrow printed on the inside of an aftermarket sanding sleeve, make sure it matches the rotation direction label on the motor. Note–The Model G0518 uses 4"D x 9"W sanding sleeves. The Grizzly Catalog offers a wide range of available grits to suite Figure 13. Sliding the sanding sleeve over the sanding drum. just about any sanding operation. ! Rotational Direction Label 5. Using a hand-operated bicycle tire pump, carefully inflate the sanding drum (Figure 14) to a pressure no greater than 10 PSI. ! Figure 14. Inflating the sanding drum.Arbor Nut Figure 12. Tightening the sanding drum arbor nut. G0518 Drum / Flap Sander-17- ! 2. Slide the flange and the arbor spacer onto Flap Sander the arbor, and begin threading the left-hand ! Figure 15. Sliding the flap sander onto the arbor. threaded arbor nut onto the end of the arbor (Figure 16). To attach the flap sander to the arbor: 1. Slide the flap sander onto the right-side arbor as shown in Figure 15. Arbor Nut Arbor Spacer Flange Figure 16. Flap sander with correctly mounted hardware. -18- G0518 Drum / Flap Sander 3. Using the two arbor wrenches, tighten the arbor nut to secure the flap sander onto the arbor as shown in Figure 17. Note–Use the arbor “flat” shown in Figure 11 when using the arbor wrenches to tighten the left-hand threaded arbor nut. ! Arbor Nut Figure 17. Tightening the flap sander arbor nut. Dust Collection To attach dust collection hoses to the dust hoods: Attach each dust hood to 4" hoses from your dust collection system (Figure 18). Figure 18. Dust collection hose hook-up. G0518 Drum / Flap Sander -19 Start Up Serious personal injury could result if the machine is connected to the power source during assembly or adjustment. Wait until the machine is turned off, unplugged and all working parts have come to a complete stop before you attempt to assemble or adjust the machine! Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing rolled up and long hair tied up and away from machinery. Projectiles from the machine could cause serious eye injury. Wear safety glasses at all times. Before starting the machine: 1. Read this manual and make sure you understand Section 1: Safety beginning on Page 2. 2. Make sure the acrylic eye shields are installed (Figure 10) and are covering the sanding drum and the flap sander. 3. Make sure all tools and foreign objects have been removed from the machine. 4. Review Section 3: Circuit Requirements beginning on Page 6, and make any necessary changes. Starting the machine: 1. Wear safety glasses at all times when running the sander! 2. Plug the sander into the power source. 3. Push the ON button shown i...