Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
11 SAFETY MESSAGES A WARNING Operator Instructions Personal Safety Equipment Always Read Instructions Before Includes: Use -Safety Glasses YES 0"sing Power Tools Safetv Rules Use -Safety Gloves YES @ Always Wear Safety Goggles ores seen Use Work Stations Use -Safety Boots @ Wear Hearing Protection Putting Into Service Use -Breathing Masks YES A A Avoid Prolonged Exposure T o Vibration Operating Use -Ear Protectors YES Dismantling and Assembly. Safety rules when using a 5062 Die Grinder -Use accessories rated at least 27,000 RPM. requirements when installing, using or maintaining the tool. -Prolonged exposure to vibration may cause injury. -Take care that the exhaust air does not point towards any -Readall instructions before using this tool. All operators must other person or material or substance that could be be fully trained in its use and aware of these safety rules. contaminated by oil droplets. When first lubricating a tool -Do not exceed the maximum working air pressure. or if the tool exhaust has a high oil content, do not allow -Use personal protection equipment as recommended. the exhaust air to come near very hot surfaces or flames. -Use compressed air only at the recommended conditions. -Never lay the tool down until the working attachment has -If the tool appears to malfunction, remove from use stopped moving. immediately and arrange for service and repair. If it is not -When the tool is not in use, shut off the air supply and practical to remove tool from service, then shut off the air press throttle triggerllever to drain the supply line. If the supply to the tool and write or have written a warning tool is not to be used for a period of time, first lubricate, note and attach It to the tool. disconnect from air supply and store in adry average room -If tool is to be used with a balancer or other suspension temperature environment. device, ensure that the tool is firmly attached to the -If the tool is passed from one user to a new or inexperi- suspension/support device. enced user, make sure these instructions are available to -When operating the tool, always keep the body and be passed with the tool. particularly the hands away from the working attachment -Do not remove any manufacturer fitted safety devices fixed to the tool. where fitted, i.e., wheel guards, safety trigger, speed -The tool is not electrically insulated. Never use the tool if governors, etc. there is any chance of coming into contact with live -Wherever possible, secure workpiece with clamps, a vise, electricity. etc. to make it rigid so it does not move during the work -Always when using the tool, adopt a firm footing and/or operation. Keep good balance at all times. Do not stretch position and grip the tool sufficiently only to overcome or overreach. any reaction forces that may result from the tool doing -Try to match the tool to the work operation. Do not use a work. Do not overgrip. tool that is too light or heavy tor the work operation. If in -Use only correct spare parts for maintenance and repair. doubt, seek advice. Do not improvise or make temporary repairs. Major -In general terms, this tool is not suitable for underwater servicing and repairs should only be carried out by use or use in explosive environments -seek advice from persons trained to do so. manufacturer. -Do not lock, tape, wire, etc. the 'OnIOff valve in -Try to make sure that the work area is clear to enable the On'position. The throttle triggertlever, etc. must always work task to be performed safely. If practical and be free to return to the 'Off' position when released. possible, try to clear unnecessary obstructions before -Always shut off the air supply to the tool and press the starting work. 'On/Offl valve to exhaust the air from the feed hose -Always use air hose and couplings with minimum work- before fitting, removing or adjusting the working attach- ing pressure ratings at least 1 112 times the maximum ment fitted to the tool. working pressure rating of the tool. -Before using the tool, make sure that a shut off device has been fitted to the supply line and the ~osition is known and easilv acces- 7 Take Air From Top siblh so that the air supply tothe tool - - can be shut off in an emergency. -I Low Spot To -Check hose and fittings regularly for Compressor Trap Water wear. with Sufflcienl Capacity -Take care against entanglement of the To Maintain Recommended moving parts of the tool with clothing, Working Pressure At 11 hair, ties, cleaning rags, rings, EachTool Outlet jewelry, watches, bracelets, etc. This could cause the body or parts of the body to be drawn towards and in con- Drain Daily tact with the moving parts of the tool L and could be very dangerous. Filter Lubricator -It Is expected that users will adopt safe working practices and observe all RecommendedAir Supply System -- local, regional or country legal Figure 1 Page No 1 Foreseen Use Of The Tool -5062 This die grinder is primarily designed for use with bondedabrasive mounted...