Assessments - 5, GPA: 4
(
)
)
|
Fotos e especificações Makita GV5010 |
Facilidade de uso
accessory. Accessory may kickback over your 9. Keep bystanders a safe distance away from hand. work area. Anyone entering the work area c) Do not position your body in the area where must wear personal protective equipment. power tool will move if kickback occurs. Fragments of workpiece or of a broken accessory Kickback will propel the tool in direction opposite to may fly away and cause injury beyond immediate the wheel’s movement at the point of snagging. area of operation. d) Use special care when working corners, 10. Hold power tool by insulated gripping sharp edges etc. Avoid bouncing and snagging surfaces only, when performing an operation the accessory. Corners, sharp edges or bouncing where the cutting accessory may contact have a tendency to snag the rotating accessory hidden wiring or its own cord. Cutting and cause loss of control or kickback. accessory contacting a "live" wire may make e) Do not attach a saw chain woodcarving blade exposed metal parts of the power tool "live" and or toothed saw blade. Such blades create shock the operator. frequent kickback and loss of control. 11. Position the cord clear of the spinning Safety Warnings Specific for Sanding Operations: accessory. If you lose control, the cord may be 18. Do not use excessively oversized sanding disc cut or snagged and your hand or arm may be paper. Follow manufacturers pulled into the spinning accessory. recommendations, when selecting sanding 12. Never lay the power tool down until the paper. Larger sanding paper extending beyond accessory has come to a complete stop. The the sanding pad presents a laceration hazard and spinning accessory may grab the surface and pull may cause snagging, tearing of the disc or the power tool out of your control. kickback. 13. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. 19. Check the backing pad carefully for cracks, damage or deformity before operation. Replace cracked, damaged or deformed pad immediately. 4 20. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on a sander frequently kick and cause loss of control leading to personal injury. 21. Hold the tool firmly. 22. Keep hands away from rotating parts. 23. Make sure the abrasive disc is not contacting the workpiece before the switch is turned on. 24. When sanding metal surfaces, watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 25. Do not leave the tool running. Operate the tool only when hand-held. 26. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. 27. Check that the workpiece is properly supported. 28. Pay attention that the wheel continues to rotate after the tool is switched off. 29. This tool has not been waterproofed, so do not use water on the workpiece surface. 30. Ventilate your work area adequately when you perform sanding operations. 31. Use of this tool to sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. 32. Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 33. If working place is extremely hot and humid, or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety. 34. Do not use the tool on any materials containing asbestos. 35. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. 36. Always use the correct dust mask/respirator for the material and application you are working with. 37. Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply ( use non metallic objects ) and avoid damaging internal parts. SAVE THESE INSTRUCTIONS. USD201-2 Symbols The followings show the symbols used for tool. . volts . amperes . hertz . alternating current . no load speed . Class II Construction . revolutions or reciprocation per minute FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action 1. Lock button 2. Switch trigger 1 2 008945 CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. • Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and maintain firm grasp on tool. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigge...
Este manual também é adequado para os modelos :Máquinas e acabar - GV6010 (468.12 kb)