Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it Battery cartridge Set plate i from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the bat- tery cartridge are on the same sides as their respective markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. The charging light will come on and charg- ing will begin. If the charging light does not come on, press the reset button. If the charging light goes out within 10 seconds even after pressing the reset button a couple of times, the battery cartridge is dead. (CAUTION :Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION : 0 Your new battery cartridge is not charged. You will need to charge it before use. 0 If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Attaching the abrasive paper *Pull out the clamp lever and insert the paper end. Be careful to maintain the proper paper tension. Align edges of paper with either edge of the pad. (Pre- bending the paper makes attachment easier.) Once the paper is in place, return the clamp lever to its original position. After inserting the paper, make sure the teeth of the clamper hold it securely. Otherwise the paper will be loose and subject to slippage, resulting in uneven sanding operation. \ Clamper I Clamp lever Ll Switch action *To start the tool, simply push the switch button. Release the switch button to stop. CAUTION : Before inserting the battery cartridge into the tool, be sure the switch actuates pro- perly. Operation *A finishing sander is generally used to re- move only a small amount of material at a time. Since the quality of the surface is more important than the amount of stock removed, do not bear down on the sander. Keep the base flush with the material at all times. Undue pressure may damage the paper and shorten tool life. CAUTION : Never run the tool without paper. YOU may seriously damage the pad. *You can put a high polish on furniture or other fine surfaces by using a cloth under the sander. Switch button I I CAUTION : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Abrasive papers Fast charger Model DC7100 12 V Fast charger Model DC7012 0 Battery cartridge 7000 Part No. 632003-2 Battery holster Part No. 823033-3C Holster holds extra battery Aug 17 84 US CORDLESS FINISHING SANDER Model 90350 Note: The switch and other part configurations may differ from country to country. MODEL 90350 Sep -19-'84 US 'FoMGDDESCRIPTION ""0" A&, DESCRIPTION 1 1 Housing SeI 1WNh Item 91 Ballancel 2 1 Name Plate Flat Washer 7 3 4 Rivet 0 5 16 1 Ball Bearing 627LLUX 4 1 Bsllery Holder 17 1 Flat Washer 5 5 1 Compression Spring 6 10 1 Countersunk Head Screw M4x10 6 1 Switch 19 2 Foot 7 8 Pan Head Screw M4x22 1With Washer1 20 2 Clamper 8 1 Push Rod 21 i Base 9 1 Housing Set [With Item I1 22 4 Pan Head Screw M4x12 [With Washeil 10 1 Motor 24 1 Rubber Pin 4 11 1 Spindle 25 1 Rubber Pin 4 12 1 Ball Beari...
Este manual também é adequado para os modelos :Máquinas e acabar - 9035DW (633.36 kb)