Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Specific Safety Rules 1. Always use proper guard with grinding wheel. A guard protects operator from broken wheel fragments. 2.Accessories must be rated for at last the speed recommended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury. 3.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 4. Keep guards in place. 5.Use only wheels having a maximum operating speed at least as high as "No Load RPM" marked on the tool's nameplate. When using depressed center wheels, be sure to use only fiberglass-reinforced wheels. 6.Check the wheel carefully for cracks or damage before operation. Replace cracked or damaged wheel immediately. 7. Use only flanges specified for this tool. 8.Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage. 9. Hold the tool firmly. IO.Keep hands away from rotating parts. 11. Make sure the wheel is not contacting the workpiece before the switch is turned on. 12.Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. 13.Use the specified surface of the wheel to perform the grinding. 14.Watch out for flying sparks. Hold the tool so that sparks fly away from you and other persons or flammable materials. 15.Do not leave the tool running. Operate the tool only when hand-held. 16.Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. 17. Check the backing pad carefully for cracks, damage or deformity before operation. Replace cracked, damaged or deformed pad immediately. 18.Hold the tool firmly. 19.Keep hands away from rotating parts. 20.Make sure abrasive disc is not contacting the workpiece before the switch is turned on. 21.Do not leave the tool running. Operate the tool only when hand-held. 22.Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. SYMBOLS The followings show the symbols used for tool. ................................. volts ............................ ................................. herts ................ .........kilograms ............................. ............................. ..................... seconds ................................. alternating current ... .................... direct current ................................. alternating or direct current ................................. Class II Construction ... splash-proof construction ............................ watertight construction revolutions or reciprocation per minute ........ ......number of blow Installing side grip (auxiliary handle) I Always install the side grip on the tool securely before operation. The side grip can be installed in any of three positions on the sides of the tool, whichever is convenient and keeps the guard properly positioned. Always hold the tool’s switch handle and the side grip firmly with both hands during operation. WARNING: Side grip only in such a way that grinding wheel will not contact any part of your body and that wheel guard always remains positioned as a barrier between the grinding wheel and the operator. Failure to do so may result in serious injury. Installing or removing abrasive disc CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing the disc. NOTE: Use sander accessories specified in this manual. These must be purchased by separate. Mount the rubber pad onto the spindle. Fit the disc on over the rubber pad and screw the lock nut onto the spindle. Lock nut To tighten the lock nut, press the shaft lock 1 firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. Lock nut wrench r Shaft lock 3- I To remove the disc, follow the installation procedure in reverse. IF USED AS A GRINDER NOTE: Use grinder accessories specified in this manual. These must be purchased by separate. WARNING: Always use guard assembly or accessory kit, noted below, for type 27 depressed center wheel. Guard assembly Part No. 192578-8 ... For 180 mm (7") Part No. 192588-5 ... For 230 mm (9") Installing wheel guard When using a depressed center wheel or an abrasive cut-off wheel, always use a wheel guard. Mount the wheel guard with the tab on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard 160 degrees counterclockwise. Be sure to tighten the screw securely. Guard accessory kit Part No. 192606-9 ... For 180 mm (7") Part No. 192607.7 ... For 230 mm (9") [-Wheel guard Installing or removing depressed center wheel CAUTION: Always be sure that the tool is switched off and unplugged befo...