Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUSINJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the name plate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Hold the tool firmly. 2. Do not leavethe tool running. Operate the tool only when hand-held. 3. This tool has not been waterproofed, so do not use water on the workpiece surface. SAVE THESE INSTRUCTIONS. Attaching abrasive paper CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the paper. Raise the lever. Insert the paper end into the clamper, aligning the paper edges even and parallel with the sides of the base. (Prebending the paper makes attachment easier.) Once the paper is in place, return the lever to its original position. Repeat the same process for the other end of the base, maintaining the proper paper tension. CAUTION: After inserting the paper, make sure the teeth of the clamper hold itsecurely. Otherwise the paper will be loose and subject to slippage, resulting in uneven sanding operation. Punch plate (standard equipment for Model BO4550 optional accessory for Model 8045502) When using the dust bag, make holes in the paper using the punch plate as follows: Hold the tool with the paper surface facing up. Place the punch plate over the paper so that the bent sides of the punch plate are flush with the paper edges. Then press the punch plate to make holes inthe paper. CAUTION: Be sure to remove the punch plate before operation. Dust bag (standard equipment for Model BO4550 optional accessory for Model 8045502) The use of the dust bag makes sanding operations clean and dust collection easy. To attach the dust bag, fit the bag's entry port onto the dust spout on the tool so that the hole in the entry port is just over the protrusion on the dust spout. For the best results, empty the dust bag when it becomes about half full, tapping it lightlyto remove as much dust as possible. Switch action To start the tool, move the switch to the "ON" position. To stop, move the switch to the "OFF" position. Operation Hold the tool firmly. Turn the tool on and wait until it attains full speed. Then gently place the tool on the workpiece surface. A finishing sander is generally used to re- move only a small amount of material at a time. Since the quality of the surface is more important than the amount of stock removed, do not bear down on the tool. Keep the base flush with the workpiece at all times. Excessive pressure may damage the paper and shorten tool life. CAUTION : 0 Do not block motor vent with your finger or hand. 0 Never run the tool without paper. You may seriously damage the pad. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. The tool will stop when the carbon brushes wear to a certain length. When this occurs, both carbon brushes should be replaced. To maintain product SAFETY and RELlABlLITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Abrasive papers / \ l;; j 742509-3 1 742510-8 Coarse Medium 150 742511-6 Fine \\\ Dust bag Part No. 166027-1 Punch plate Part No. 163247-8 MODEL BO4550 MACHINE .- MACHINE 2 2 1 1 1 1 1 1 2 1 1 1 1 1 2 2 - Bush Holder Carbon Brush Bal~Beain--626LLB ARMATURE ASSEMBLY (With Item 3, 4, 7, & 8) Housing Set (With Item 26) FIELD ASSEMBLY Flat Washer 9 Hall Bearing 629LLB Tapping Screw BT 4x16 Name Plate Fan A3 Discseal 10 Ball Bearing 6200LLB Fan Guide Foot ClamDer 17 18 19 20 21 22 23 24 25 26 27 28 29 - 4 1 1 1 2 1 1 1 1 1 1 1 2 - Pan Head Screw M4x12 (With Washer) Rubber Sleeve 48 Flat Washer 6 Countersunk Head Screw M4x12 Lever Base Dust Bag Cord Switch Housing Set (With Item 5) Tapping Screw BT 4x40 Tapping Screw BT 4x25 Tapping Screw BT 4x50 FINISHING SANDER Model BO4550 Model BO45502 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leav...
Este manual também é adequado para os modelos :Máquinas e acabar - BO4550 (479.45 kb)