Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
To help you do this please read the accompanying operating instructions. Keep these instructions in a safe place. If you pass the device on to anyone else, please ensure that you also pass on all the documentation. • Proper use The device is intended for the dry cutting, rough grinding and brushing of metal and stone. Any other use or modification to the device shall be considered as improper use and could give rise to considerable dangers. We will not accept liability for loss or damage arising from improper use. The device is not intended for commercial use. Note: Slots cut in load-bearing walls must comply with standard DIN 1053 Part 1 or the regulations applicable in your country. These instructions and advice must be observed. Before you start a task, seek the advice of a competent structural engineer, architect, or the relevant site management staff. • Features and equipment Hand grip (rotatable) ON / OFF switch Safety lock-out Unlocking button Carbon brushes cover Auxiliary handle Disc guard cover Clamping lever Coded projection Adjuster screw Spindle lock button Threaded hole (3 x) for auxiliary handle Clamping nut (see Fig. G) Mounting spindle (see Fig. G) Mounting flange (see Fig. G) 6 GB/IE/CY III PARKSIDE Introduction / General safety advice for electrical power tools Coded groove (see Fig. G) Spanner Roughing / grinding disk* Cutting disc for metal* Cutting disc for masonry* * not included • Included items Angle grinder PWS 230 SE Auxiliary handle Disc guard cover Spanner Operating instructions A General safety advice for electrical power tools HWARNin |GJ Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury. KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE! THE TERM “ELECTRICAL TOOL" USED IN THE SAFETY ADVICE REFERS TO ELECTRICAL TOOLS POWERED BY MAINS ELECTRICITY (BY MEANS OF A MAINS LEAD) AND ELECTRICAL TOOLS POWERED BY RECHARGEABLE BATTERIES (WITHOUT A MAINS LEAD). • Technical information 1. Workplace safety Rated voltage: Rated power consumption: No-load speed: Grinding disc: Mounting spindle: Protection class: 230 V ~ 50 Hz 2000 W no 6500 min-1 0 230 mm M14 / threaded II /n Noise and vibration data: Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level of the electrical power tool are typically: Sound pressure level: 92 dB(A) Sound power level: 108 dB(A) Uncertainty K: 3 dB a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents. b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes. Keep children and other people away while you are operating the electrical tool. Distractions can cause you to lose control of the device. Wear ear protection! Evaluated acceleration, typical: Hand / arm vibration ah = 11,95 m / s2 Uncertainty K = 1,5 m / s2 2. Electrical safety A To avoid danger to life from electric shock: a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock. III PARKSIDE GB/IE/CY 7 General safety advice for electrical power tools b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed. c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock. d) a Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock. e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock. f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock. 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. b) Wear personal protective fSvSh equipment and always wear '3''®' safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety sho...