Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Please make sure you familiarise yourself fully with the way the equipment works before you use it for the first time and that you understand how to handle electrical power tools correctly. Please read the operating instructions below and the accompanying safety advice ! carefully. Use the equipment only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce better results. We hope you enjoy using your sander. FEATURES OF THE PSS 260 TECHNICAL INFORMATION Nominal power: 260 W Low load speed: no 7,000 – 11,000/min Orbits: max. approx. 22,000/min Pad size: 225 x 115 mm Orbit: 2.1 mm Sanding sheet size max: approx.: 280 x 115 mm Protection class: II IMPORTANT SAFETY ADVICE ! Clip Sanding sheet Base Air vents Dust bag adapter Paper dust bag Handle ON / OFF switch Adjuster wheel Continuous operation locking button Dust extraction nozzle (Fig.) , ,, = accessories supplied Nominal voltage: 230 V ~ 50 Hz Dust extraction system: built-in extraction system / or with exterior suction device Weight: 2.25 kg The A weighted noise level of the equipment is typically: Sound pressure level: 70.0 dB(A) The acceleration value is typically 2.5 m/s2 (vibration) • To be read in conjunction with the advice in the accompanying booklet on safety. • The sander is not designed for wet sanding and therefore is only to be used for dry sanding • Do not use the sander on materials containing asbestos • Look after your health: Wear ear defenders - also wear safety glasses and a breathing /dust mask • Take note that working with stone and wood can give rise to dusts that can damage your health. • Always keep the power cable well out of the sander's working area and fed to the rear of the machine. OPERATION Take note of the mains voltage. The voltage must agree with that shown on the identification plate (equipment shown as 230 V can also be used with 220 V). 4 SWITCHING ON AND OFF When using the orbital sander you can select between continuous and non-continuous operation (see Fig. ). For short periods of sanding use the non-continuous setting and for longer periods use the continuous setting. Select your chosen setting as follows: SWITCH ON NON-CONTINUOUS OPERATION: press ON/OFF switch . SWITCH OFF NON-CONTINUOUS OPERATION: release ON/OFF switch . SWITCH ON CONTINUOUS OPERATION: press ON/OFF switch and with it still pressed fix it in place by pressing the continuous operation locking button . SWITCH OFF CONTINUOUS OPERATION: press on/off switch and release it again. SETTING THE SPEED You can set the required speed using the adjuster wheel (see Fig ) as required. As the setting depends on what kind of material you are working with, use the recommendations and examples given in Tips and Tricks. FITTING THE SANDING SHEETS Note: before fitting a new sanding sheet, remove dust and dirt from the base . 1. Lift both clips to open them to insert a new sanding sheet or change the sanding sheet for use on a different material. 2. Push the sanding sheet under the open clip at one end and clamp it securely on the base by moving the clip down again. 3. Do the same at the other end. Make sure that the sanding sheet is tight against the base. See Figures and . 4. Important! - The holes in the sanding sheet and the base must align for the dust to be extracted through the base. See Figure . Different materials need different grades of sanding sheets. To determine which grade is suitable for your work, please read our recommendation in Tips and Tricks. DUST EXTRACTION • DUST EXTRACTION WITH PAPER DUST BAG Push the paper dust bag on to the adapter . Ensure that the adapter fits correctly into the holder. Clip the dust bag with the adapter to the side of the sander. • DUST EXTRACTION WITH VACUUM CLEANER For dust extraction using a vacuum cleaner use the appropriate connector – see Figure . Attach the adapter to the end of the vacuum cleaner hose and clip it to the side of the equipment. 5 MAINTENANCE OF THE ORBITAL SANDER 1. Clean the sander regularly. For the best results do this straight after the work has been completed. 2. Do not allow liquids to get inside the sander. Use a soft cloth for cleaning the housing. Do not use petrol, solvents or cleaners that may attack the plastic. 3. Air vents must always be clear and clean. ADVICE ON WORKING METHODS, TIPS AND TRICKS • You can use the PSS 260 orbital sander for effortless sanding even on large areas, see Fig. . • Move the orbital sander in parallel broad circles or in alternate longitudinal and transverse directions. • Do not press on the orbital sander. This damages the sanding sheets and adversely affects sanding performance. • From time to time clean the sanding sheet with a vacuum cleaner. • You do not have to resand any areas when working up to edges. The orbital sander works right into the corners because its housing is continuous with the edge of the sanding sheet, see Fig. . • The integrated dust extraction system allows...