Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals. WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. CAUTION: Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. The label on your tool may include the following symbols. V ..........................volts A..........................amperes Hz ........................hertz W ........................watts min........................minutes ......................alternating current ......................direct current no........................no load speed ..........................Class IIConstruction ........................earthing terminal ........................safety alert symbol .../min..................revolutions or 1246358FIG. 1 7reciprocations per minute 1. MEDIUM GRINDING WHEEL (60 GRIT) /MEULE A GRAINS MOYENS (NO 60) / RUEDA DE ESMERIL, MEDIA (GRANO 60) 2. COARSE GRINDING WHEEL (36 GRIT) / MEULE A GROS GRAINS (NO 36) / RUEDA DE ESMERIL, GRUESA (GRANO 36) 3. INTEGRATED LIGHTS / LAMPES INTEGREES / LUCES INTEGRADAS 4. EYE SHIELDS / PROTEGE-YEUX / PANTALLAS PROTECTORAS DE OJOS 5. TOOL RESTS / APPUIS / SOPORTES DE LA HERRAMIENTA 6. SWITCH (ON-OFF) / INTERRUPTEUR DE MARCHE / ARRET / INTERRUPTOR ARRANQUE/PARADA (ON-OFF) 7. MOUNTING HOLES / ORIFICES DE MONTAGE / HUECOS DE MONTAJE 8. QUENCH TRAY / ETEIGNEZ LE PLATEAU / APAGUE LA BANDEJA FIG. 2 1 2 3 4 5 6 7 8 FIG. 3 SPARK GUARD PARE- ETINCELLES GUARDACHIS- PAS EYE SHIELD PROTEGE-YEUX PANTALLA PROTECTORA DE OJOS FIG. 4 L’APPUI RECEPTACULO PARA EL SOPORTE DE LA HERRAMIENTA TOOL REST BRACKET APPUI DE L’OUTIL SOPORTE DE LA HER- RAMIENTA FIG. 4 L’APPUI RECEPTACULO PARA EL SOPORTE DE LA HERRAMIENTA TOOL REST BRACKET APPUI DE L’OUTIL SOPORTE DE LA HER- RAMIENTA TOOL REST FERRURE DE MOTOR Be sure your power supply agrees with the nameplate marking. 120 Volts, 60Hz means alternating current only should be used to operate this tool.A power decrease of more than 10% will cause loss of power and overheating. All Black and Decker tools are factory tested; if this tool does not operate, check the power supply. BENCH MOUNTING 1. The grinder should be unplugged. 2. Position grinder on workbench. Check for the availability of power for the grinder. Mark location of holes for drilling. 3. Drill appropriate sized holes. 4. Insert 1/4” (6mm) Hex head bolts through washers and the holes. You may want to use washers on the underside of the bench as well. 5. Tighten the nuts. Do not overtighten. Allow the rubber feet to absorb the vibration when the grinder is running. Assembly Note: Approximate assembly time is 30 minutes. Tools Required: 10mm and 12mm wrenches or adjustable wrench. INSTALLING SPARK GUARDS, LIGHT FIXTURES, EYE SHIELDS AND QUENCH TRAY TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY There are seven seperate hardware bags and a quench tray packed with your bench grinder. Hardware bag #’s 1,2, 3 and 4 shown in Figure 2 are used to assemble the spark guard, light fixture and eye shield assemblies shown in Figure 3. To begin assembly insert the 1/2” long machine screw with washer through the slot of the left side spark guard and into the threaded hole located at the top of the inner metal wheel guard. Adjust the edge of the spark guard to within 1/16” of the grinding wheel or other accessory. Tighten the screw securely. Continue to adjust spark guard to be within 1/16” of grinding wheel or other accessory as wear occurs. Align the left side spark guard with the opening below the left side light fixture. Next, align the clear plastic eye shield (rib side up per Figure 3) with the left side spark guard. With the three items aligned, insert the 3-1/2” bolt through them from the left side insuring that the square portion of the bolt head is seated fully into the square eye shield recess. Place a knob and washer onto the threaded end of the bolt and hand tighten. Adjust the eye shields so they are between the wheels and your eyes. Tighten the shields in place by tightening the plastic knob in the assembly by hand. NOTE: EYE SHIELDS ARE NOT DESIGNED TO REPLACE SAFETY GLASSES. Repeat the procedure for the right side assembly inserting the 3-1/2” bolt from the right side. A quench tray is included for use in cooling the workpiece after the grinding process. The tray can be filled with water (only use water) and attached to either side of the grinder by aligning the tabs on the side of the tray with the slots on the outer sides of the wheel guards. INSTALLING TOOL RESTS TURN OFF POWER AND...
Este manual também é adequado para os modelos :Máquinas e acabar - Fire Storm 622351-00 (203.35 kb)