Assessments - 4, GPA: 3.8 ( )

Fabricante : Craftsman Arquivo Tamanho: 1.75 mb Arquivo Nome : Língua de Ensino:

I Hunger, Cable ........................... 1 0 Owner's Manual ........................... t G "S'" Clip ............................... 3 P 9" Abrasive Disc .......................... 1 H Pan Head Screw, Type 23, 10-32 x 1/2 ........ 3 J Base and Belt, Table (w/Sanding Belt) ......... t Q Sanding Disc (w/Set Screw) .................. 1 R Belt,Sanding .............................. 1 K Disc Dust Trap .......................... t -Bag Assembly, Outlet (Part No. 68064) L Oust Trap Cover ......................... 1 (Containing the following loose parts): S Outlet, on/off Power ...................... 1 M Work Table ............................. 1 N Bag (containing the following loose parts) T Switch Key ............................. 1 (Part No. 68035) U Bracket, Switch Mounting .................. t Motor Pulley, 2 In. Oia................... 1 V Screw, Pan Hd. 8 x 3/8 .................... 3 Wrench, 1/2" . ......................... 2 5/32 Setscrew Wrench ................... 1 W Lockwasher, 114" . ....................... 2 X Screw; Pan Hd. Machine 1/4-20 x 1/2 ......... 2 Flat Head Machine Screw 10-32 x 1-3/4 ...... 4 assernbJy H The following parts are included with Model 113.225931 ONLY. Item No. Qty. *Loose Parts Bag Part #68062Containing Following items: *A Nut, Hex Head 1/2-13 ........................ 8 *A Nut Hex 1/4-20 .............................. 32 *B Screw Truss Hd. 1/4-20 x 5/8 ................. 32 *C Lockwasher, 1/4 External .................... 32 *D Foot, Leveling .............................. 4 E Motor ...................................... 1 F Leg ......................................... 4 G Channel,Support ........................... 2 H Stiffener, Side .............................. 2 J Stiffener, End ............................... 2 K Support, Motor ............................. 1 P Bracket, Mounting ........................... 1 F• HAROWABETOOL& MOTOR FORMOUNTING *L Screw, Hex Hd. 5/16-18 x 1-1/2 ............... 2 *C Lockwasher Ext. 5/16 ....................... 6 *A Nut, Hex 5116-18 ............................ 6 K *M Washer11132ID ............................ 6 *N Bolt, Carriage 5116-18x 314 .................. 4 NP D L E END STIFFENER HEX NUT SCREW _1 | LOCKWASHER 1. Assemble the two (2) End Stiffeners and the two 2 Side Stiffeners using four (4) 1/4-20 Truss head screws. The End Stiffeners are placed On top of each Side Stiffener as shown. Insert screws through the 9/32 inch diameter holes and finger tighten 1/4-20 nutS. 2. Attach the four (4) legs to the side and End Stiffener using 1/4-20 screws, Iockwashers and nuts as shown. 3. Remove the four (41 Truss head screws which were assembled in Paragraph No. One. Place the two (2 Support Channels as shown, in position align holes in supports with holes in the Stiffeners, replaceIockwashers and nuts, Tighten all nuts using 7/16 wrench. 4. Assemble the motor support to steel legs with 1/4-20 screws and nuts. Motor support can be mounted to either end of stand. Tignlen nuts 5. Install leveling feet as shown. To level Leg Set, loosen nut on inside of leg and turn nut on outside to raise or lower feet. Adjust alt four levelers, if necessary, and then tighten nuts on inside of leg. NOTE: These levelers are not intended for height adjustment. S,DE ST,FFEN R STIFFENER SIDE STIFFENER LOCKWASHER \ HEX NUT __ _e .r _ CH/%NNEL SUPPORT \ CHANNEL SUPPORT LEG SCREW _ k _. MOTOR SUPPORT LEG / SCREW / LOCKWASHER NUT WHEN INSTALLING OR MOVING THE SANDER. AVOID DANGEROUS ENVIRONMENT, dry, indoor place protected from rain. lighted. Use Keen the sander work area n a well Place forced the sander so neither the user to stand in line with the abrasive nor bystanders belt or d sc. are To avoid injury from unexpected sandel movement: = Put the sander on a firm of room for handling workpiece. level surface where there is plenty and properly supporting the -Support the sander so it does not rock. ,,Bolt the sander tothe walk. or slide during floor or work normal use. surfaceif it tends to slip, To avoid back injury, get when you need to move need to lift the sander. help or use recommended the sander. Always get casters help if you NEVER STAND ON TOOL. too] tips or you accidentally anything above or near the the tool to reach them. Serious injury could occur if the hit the cutting tool, Do not store toot where anyone might stand on # MOTOR MOUNT BRACKET THISSIDE MOUNTING CRAFTSMAN BELT AND DISC STEEL LEG SET. SANDER ON CATALOG NO. 9-22236 0 C OOc NOTE: Forillustrative purposes, the Belt and Disc Sander is o°o ° shown mounted on the Craftsman Catalog No. 9-22236 oo Steel Leg Set. This Leg Set is included with Model No. ___c oc 113.225931. 1. )lace the 3elt and Disc Sander on the Steel Legs, 2. Mount to legs using two 5_16-18 x 2-1/2'" hex head position as shown, ane align the mounting qoles n screws, flat washers, externa! Iockwashers. ana hex the feet of the Belt and Disc Sander with those in the nuts. END STIFFENERS marKea with an X n tne Jllustratior !. NOTE: The a...

Baixe o seu

Para fazer o download, introduza 2 dígitos :