Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Such preventive safety measures reduce the risk of starting the tool accidentally. A WARNING Models 100 & 200 High Speed Rotary Tools SWITCH (100 SINGLE SPEED) (200 TWO SPEED) COLLET. WRENCH -eC Model 3000 High Speed Rotary Tool EZ TWIST™ SHAFT LOCK INTEGRATED BUTTON WRENCH/NOSE CAP (Model 3000 only) ON/OFF SWITCH HANGER COLLET NUT CORD VENTILATION OPENINGS VENTILATION OPENINGS BRUSH COVER (one on each side) Model number Voltage rating Amperage rating No load speed Collet capacities 100 120V 50 - 60Hz 1,15A n0 35,000/min 1/32, 1/16", 3/32", 1/8" 200 120V 50 - 60Hz HI 1,15A, LO 0,80A n0 15,000/35,000/min 1/32, 1/16", 3/32", 1/8" 3000 120 V 50 - 60Hz 1,2A n0 5,000-32,000/min 1/32, 1/16", 3/32", 1/8" 8 DM 2610015339 05-11:DM 2610015339 05-11.qxp 5«/11 9:40 AM Page 9 Assembly A WARNING Always unplug Rotary Tool before changing accessories, changing collets or servicing your Rotary Tool. A CAUTION COLLET NUT — To loosen, first press shaft lock button and rotate the shaft by hand until the lock engages the shaft preventing further rotation. Do not engage lock while the Rotary Tool is running. With the shaft lock engaged use the collet wrench to loosen the collet nut if necessary. The collet nut must be loosely threaded on when inserting an accessory. Change accessories by inserting the new one into the collet as far as possible to minimize runout and unbalance. With the shaft lock engaged, finger tighten the collet nut until the accessory shank is gripped by the collet. Avoid excessive tightening of the collet nut when there is no bit inserted. EZ TWIST™ INTEGRATED WRENCH/NOSE CAP (Model 3000 only) The nose cap of your tool has an integrated wrench allowing you to loosen and tighten the collet nut without the use of the standard collet wrench. Unscrew the nose cap from the tool, line-up steel insert on inside of cap with collet nut. With the shaft lock engaged twist nose cap clockwise to tighten, and counterclockwise to loosen. COLLETS — Four different size collets (see illustration), to accommodate different shank sizes, are available for your Rotary Tool. To install a different collet, remove the collet nut and remove the old collet. Insert the unslotted end of the collet in the hole in the end of the tool shaft. Replace collet nut on the shaft. Always use the collet which matches the shank size of the accessory you plan to use. Never force a larger diameter shank into a collet. Note: Most rotary tool kits do not include all four collets sizes. A CAUTION COLLET IDENTIFICATION CHART Collet sizes can be identified by the rings on the back end of collet. 1/32" Collet has one (1) ring. 1/16" Collet has two (2) rings. 3/32" Collet has three (3) rings. 1/8" Collet has no rings. (Included in most tool kits on the tool) 9 DM 2610015339 05-11:DM 2610015339 05-11.qxp 5/ff/11 9:40 AM Page 10 BALANCING ACCESSORIES - For precision work, it is important that all accessories be in good balance (much the same as the tires on your automobile). To true up or balance an accessory, slightly loosen collet nut and give the accessory or collet a 1/4 turn. Retighten collet nut and run the Rotary Tool. You should be able to tell by the sound and feel if your accessory is running in balance. Continue adjusting in this fashion until best balance is achieved. To maintain balance on abrasive wheel points, before each use, with the wheel point secured in the collet, turn on the Rotary Tool and run the 415 Dressing Stone lightly against the revolving wheel point. This removes high spots and trues up the wheel point for good balance. The hanger is provided for the use of hanging your tool while using the flex-shaft or for storage. If you do not use the hanger, remove it from the tool and snap it back into place underneath the cord so it will be out of the way while the tool is in use. Operating Instructions The Rotary Tool is a handful of high-speed power. It serves as a carver, grinder, polisher, sander, cutter, power brush, drill and more. The Rotary Tool has a small, powerful electric universal motor, is comfortable in the hand, and is made to accept a large variety of accessories including abrasive wheels, drill bits, wire brushes, polishers, engraving cutters, router bits, cutting wheels and attachments. Accessories come in a variety of shapes and permit you to do a number of different jobs. As you b e com e fami li ar wi th th e ran g e of accessories and their uses, you will learn just how versatile the Rotary Tool is. You’ll see dozens of uses you hadn’t thought of before. The real secret of the Rotary Tool is its speed. To understand the advantages of its high speed, you have to know that the standard portable electric drill runs at speeds up to 2,800 revolutions per minute. The Rotary Tool operates at speeds up to 35,000 revolutions per minute. The typical electric drill is a low-speed, high torque tool; the Rotary Tool is just the opposite - a high-speed, low torque tool. ...
Este manual também é adequado para os modelos :Máquinas e acabar - 200 (1.34 mb)
Máquinas e acabar - 3000 (1.34 mb)