Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Note: When using an adapter, the adapter must be grounded. This equipment must be grounded. Verify that any existing electrical out- let and circuit you intend to plug into is actually grounded. If it is not, it will be necessary to run a separate 12 AWG copper grounding wire from the outlet to a known ground. Under no circumstances should the grounding pin from any three-pronged plug be removed or serious injury may occur. Figure 2. Never remove the grounding pin! -6 M1104, M1105, M1106 Heavy-Duty Bench Grinder SET UP Unpacking Your SHOP FOX® Bench Grinder has been carefully packaged for safe transporting. If you notice the machine has been damaged, please contact your authorized SHOP FOX® dealer immediately. Inventory The following is a description of the main components shipped with your bench grinder. Lay the components out and use the list below and Figures 3 & 4 to inventory your package. Box Inventory: Qty. A. Left Lens Hanger (Eye Shield)...........................1 Right Lens Hanger (Eye Shield) (Not Shown)..........1 B. Toothed Flange Scr M6-1.25 x 13mm (Eye Shield) ...2 C. Lock Washer 7mm (Eye Shield) .........................2 D. Flat Washer 7mm (Eye Shield) ..........................2 E. Female Knob M6-1.25 (Eye Shield) .....................2 F. Hex Bolt M6-1.25 x 10mm (Eye Shield) ................4 G. Flat Washer 7mm (Eye Shield) ..........................4 H. Left Spark Arrestor (Eye Shield) ........................1 Right Spark Arrestor (Eye Shield) .......................1 I. Lens (Eye shield) (Not Shown)...........................2 J. Nut Plate (Eye Shield) ....................................2 K. Phlp Hd Scr #10-24 x 3.8" (Eye Shield) .................4 L. Left Tool Rest .............................................1 Right Tool Rest (Not Shown).............................1 M. Flat Washer 8mm (Tool Rest) ...........................4 N. Hex Bolt 5.16"-18 x 3.4" (Tool Rest)......................4 Heavy-Duty Bench Grinder Unit (Not Shown) .........1 If any parts are missing, examine the packaging for the missing parts. For any missing parts, find the part number in the back of this manual and contact Woodstock International, Inc. at (360) 734-3482 or at techsupport@ shopfox.biz NOTICE If ordering replacement parts, refer to the parts list and diagram in the back of the manual. I Figure 3. Left eye shield assembly. K J E C B A D H G F N Figure 4. Left tool rest and hardware. L M SET UP -7 M1104, M1105, M1106 Heavy-Duty Bench Grinder SET UP Shop Preparation • Working Clearances: Consider existing and anticipated needs, size of material to be processed through the machine, and space for other machinery when establishing a location for your new machine. • Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain. • Electrical: Electrical circuits must be dedicated or large enough to handle amperage requirements. Outlets must be located near each machine, so power or extension cords are clear of high-traffic areas. Follow local electrical codes for proper installation of new lighting, outlets, or circuits. Mounting The Heavy-Duty Bench Grinder must be mounted to a workbench to avoid accidental tipping. If you intend on using the grinder for portable applications, mount it to a heavy plywood base (at least 1" thick) that is wide enough to prevent tipping or rocking during use, then clamp the plywood base to the workbench or table. To mount the Heavy-Duty Bench Grinder, do these steps: 1. Determine the surface or object to which you will mount your grinder, and obtain the needed hardware for your mounting application. 2. Fasten the grinder to your supporting surface, using the dimensions in Figure 5. DO NOT overtighten the mounting bolts or you will crack the base. 3. Check the stability of the mounted grinder to make sure it is stable enough to be used safely. 4. Always make sure the grinder is bolted or clamped to the workbench, table, or grinder stand before use. MAKE your shop “child safe.” Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. NEVER allow untrained visitors in your shop when assembling, adjusting or operat- ing equipment. Figure 5. Bench grinder mounting bolt pattern. AHoles are 5.16" Diameter M1104: A = 6 5.16" M1105: A = 7 5.16" M1106: A = 8 3.4" -8 M1104, M1105, M1106 Heavy-Duty Bench Grinder Tool Rest and Eye Shield The tool rest supports the workpiece during grinding. Certain types of grinding may require jigs or accessories to assure the proper angle of the workpiece against the wheel. The eye shield must be installed and positioned between the grinding wheel and your face during grinding. The eye shield is NOT a substitute for safety glasses or a safety face shield. You must wear ANSI approved face and eye protection. Using the hardware from the Inventory list on Page 7, assemble the tool rests and eye shields as they are shown in Figures 6 & 7. Grinding Wheel Installation Before insta...
Este manual também é adequado para os modelos :Máquinas e acabar - M1104 (3.87 mb)
Máquinas e acabar - M1106 (3.87 mb)