Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
Align locating bumps on damper ring with cut outs in shroud and depress ring with thumbs until shroud seats into groove completely around ring, then tighten screws. IMPORTANT: Ring should not have bends or ripples when correctly seated. Apply a thin film of light grease to top side of backing pad where the damper ring makes contact, reassemble backing pad and firmly tighten screw. BACKING PAD DAMPER RING SHROUD LOCATING BUMPS ON UNDERSIDE OF DAMPER RING INSTALLING ACCESSORIES (Model 1295D 1295DH & 1295DVS) DUST COLLECTION CANISTER Your random orbit sander uses hook-and-loop The integral dust extraction system collects backed accessories, which firmly grip the pad sanding dust in canister supplied with your when applied with moderate pressure. To sander. For maximum efficiency, the dust change the accessory, merely peel off the old canister should be emptied frequently during accessory, remove dust from the pad if operation. necessary, and press the new accessory in When the canister is removed from the tool an place. Be sure to align the sanding disc holes (optional vacuum hose accessory) can be with the holes in the backing pad to allow the attached to the dust port. dust extraction system to function. To use this feature, attach vacuum adapter After considerable service the pad surface will and vacuum hose (optional accessories) to become worn, and the pad must be replaced dust port, then connect opposite end of the when it no longer offers a firm grip. If you are vacuum hose to a shop vacuum cleaner. experiencing premature wearout of the pad facing, decrease the amount of pressure you CLEANING AND EMPTYING are applying during operation of the tool. THE DUST CANISTER (Model 1295DP only) To empty, lift lid of canister. Knock excess Your sander is equipped with PSA backed dust out of the micro filter, or remove dust accessories with pressure sensitive adhesive. with your fingers or a soft brush. To change accessory, peel protective sheet You may notice that all the dust may not comefrom the back of accessory. Align accessory out of the canister. This will not affect sandingwith backing pad and press firmly in place. To performance but will reduce dust collectionremove, lift an edge of accessory with your efficiency. finger nail and peel it off the backing pad. NOTE: Do not wash the micro filter with soapNOTE: Do not store tool with sanding disc on and water. Dust may become more firmlypad, as sanding creates heat which increases lodged in the pores, which will reduce dustthe adhesive bond. If the disc is left in place it collection, and damage the micro filter. may become very difficult to remove. -8 BM 2610914126 9-03 10/1/03 10:31 AM Page 9 Your sander was designed to sand in small or confined areas. Its small size and light weight makes it ideal for overhead work. You may grip the tool on top or around the motor housing as shown, which was contoured for that purpose. “Tool Tips” SANDING: open-coat aluminum oxide sanding discs are recommended for most wood or metal sanding applications, as this synthetic material cuts quickly and wears well. Some applications, such as plastics, glass, or stone require silicon carbide discs, which have a very sharp cutting edge. For best results, use Bosch sanding and polishing accessories which are of superior quality and are carefully selected to produce professional quality results with your sander. With the workpiece firmly secured, depress switch while applying the pad to the work surface. DO NOT apply excessive pressure as this will slow the pad action, and DO NOT start the tool and bring it up to speed before applying to the work; swirl marks will result in either case. In general, higher speeds and moderate pressure will give the best results. If faster removal is desired, DO NOT INCREASE PRESSURE ON THE TOOL; use a coarser grade of abrasive. Move the sander in long sweeping strokes, parallel to the grain using some lateral motion to overlap the strokes by as much as 75%. The random orbit action allows cross-grain sanding, but be careful not to tilt the sander near edges, or undesirable rounding may result. If the surface is rough, begin with coarser grits and then complete the surfacing with medium and fine abrasives. Because the random orbit action is so effective, it is often possible to begin sanding with a medium grit disc and go directly to fine finishing. To avoid uneven results, do not skip more than one grit size when going from coarser to finer, and do not sand in one area for too long. When the job is completed, release switch, and gently lift the tool from the work surface at the same time. -9 POLISHING: for most polishing, the soft backing pad will give the best results. The random orbit sander may be fitted with a foam buffing pad or polishing bonnet to polish or remove scratches from painted or finished surfaces, plastics, and even glass. The tool is operated in much the same way as when sanding, but the following points should be observed; Apply the...
Este manual também é adequado para os modelos :Máquinas e acabar - 1295DH (449.16 kb)
Máquinas e acabar - 1295DVS (449.16 kb)