Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
DO NOT overexert yourself while unpacking or moving your machine—get assistance. Items Needed for Set Up The following items are needed to complete the set up process, but are not included with your machine: Description Qty • Wrench or Socket 12mm ............................ 1 • Wrench or Socket 8mm .............................. 1 • Safety Glasses (for each person) .............. 1 • Phillips Screwdriver #2 ............................... 1 • Assistant .................................................. 1-2 Inventory After all the parts have been removed from the box you should have the following items: Box 1: Qty A. Grinder ....................................................... 1 B. Wrench 25mm (G0596/G0597).................. 1 C. Wrench 50mm (G0598/G0599).................. 1 NOTICE Some hardware/fasteners on the inventory list may arrive pre-installed on the machine. Check these locations before assuming that any items from the inventory list are missing. Eye Shields The eye shields on the Model G0596/G0597/ G0598/G0599 may come pre-mounted from the factory. If they do not, attach them at this time with the two Phillips head screws provided. Light Switch Mounting Screws Figure 4. Eye shield. Mounting Mount the grinder on the optional H7834 stand (see Page 17), or a workbench that is sturdy enough to hold the weight of the machine and any downward pressure that may be applied during operation. The stand or workbench should be level, rigid, and attached to the floor, so it will not move during operation. For proper safety, drill holes in your workbench and secure the grinder with hex bolts, washers, and hex nuts, or with lag screws and flat washers. (Mounting hardware is not provided due to the many possible set ups and workbench thicknesses.) When locating your grinder, remember: • You will need room for potentially large workpieces. • Maintain easy access to dust ports for attaching dust collection system. • Grinding without dust collection system spreads dust in the immediate vicinity of the grinder. • Grinding creates flying sparks that MUST be out of reach of any flammables. • You will need a lot of light around the grinding wheel in addition to the lighted eye shields. DO NOT operate this grinder without the eye shields or wheel guards in place. Failure to properly use these safety devices could lead to serious injury! -10 G0596-G0599 Industrial Bench Grinders Dust Collection DO NOT operate the Model G0596/G0597/ G0598/G0599without an adequate dust col- lection system. This grinder creates substan- tial amounts of dust while operating. Failure to use a dust collection system can result in short and long-term respiratory illness. The Model G0596/G0597/G0598/G0599 features a dust port at the rear of the grinding wheel. If a dust collection system is not attached, both ports have spark deflectors that direct sparks downward. To connect a dust collection hose: 1. Remove the spark deflector. 2. Fit the dust hose over the dust port, as shown in Figure 5, and secure in place with a hose clamp. 3. Tug the hose to make sure it does not come off. Note: A tight fit is necessary for proper performance. Spark Deflector Dust Port Figure 5. Dust port. Test Run The test run ensures that the grinder and grinder wheels were not damaged during shipping. To test run the grinder: 1. Review and understand all grinder safety information. 2. Remove the wheels and closely inspect the overall conditions. Follow this by performing a "Ring Test" (see Wheel Inspection on Page 15 and Wheel Replacement on Page 16). 3. Plug the grinder into the power source. 4. Put on safety glasses and face shield. 5. Stand to the side of the line of the wheels rotation, turn the grinder ON, and allow it to run a least one minute, before standing in front of it. —The grinder should run smoothly. —Grinding wheels should run true without noticeable vibration. —If there is an obvious problem with the way the grinder is running, turn it OFF immediately and troubleshoot the problem, using the troubleshooting table on Page 18. DO NOT operate the grinder until it is fixed. G0596-G0599 Industrial Bench Grinders FIRE AND EXPLOSION HAZARD! DO NOT attach dust ports to a dust collection system designed or used for wood dust collection. -11 -12- G0596-G0599 Industrial Bench Grinders Hardware Recognition Chart SECTION 4: OPERATIONS Operation Safety Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses with face shield, a respirator, and hearing protection when operating this machine. Loose hair and clothing could get caught in machinery and cause serious personal injury. Keep loose clothing and long hair away from moving machinery. NOTICE If you have never used this type of machine or equipment before, WE STRONGLY RECOMMEND that you read books, trade magazines, or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will no...
Este manual também é adequado para os modelos :Máquinas e acabar - G0597 (3.91 mb)
Máquinas e acabar - G0599 (3.91 mb)