Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Always keep the grinder moving to prevent gouge marks. If you stay in one place too long, then the grinder will produce a depression in the work that will compromise your finish. Experiment in a small corner or area that is not very noticeable on your project. Ideally, you want to achieve the balance of removing defects without damaging your work. Installing Abrasive Disc or Attachments Make sure the grinder is disconnected from the power source and remove the spanner nut. Place the grinding disc or attachment over the arbor and secure it with the spanner nut. Using the wrenches provided, hold the arbor with the wrench and tighten the spanner nut with the spanner wrench. To remove abrasive discs, or attachments, follow the steps just performed. Note—Model G5968 has a spindle lock button so a wrench is not necessary on the arbor. Just push the spindle lock button on the top of the grinder to lock the spindle and use the spanner wrench to tighten or loosen the spanner nut. Using the Grinder • Inspect grinding disc for flaws. Never use a chipped or broken disc. • Use only grinding discs made for this grinder. Never use a disc that requires modifications to the grinder. • Never operate grinder without the guard in place. • Pay attention to the direction the sparks are going while grinding. Flamable material must be kept at a safe distance while grinding. • Make sure workpiece is secure. Use a vice or clamps when working with smaller workpieces. • Always use two hands to hold the grinder. • Never apply excessive force while grinding. Your grinder will last longer if you let “it” do the work. Using slight pressure barely greater than the weight of the equipment is ideal because you can still maintain control. • For added control and comfort, a lock- on trigger switch is installed. The lock- on trigger switch is easy to operate— simply squeeze the trigger and push in the locking pin. To release the trigger, press the trigger in, then release to disengage the trigger lock. -4- G5968/9 Angle Grinder MAINTENANCE General Regular periodic maintenance on your Model G5968/9 Angle Grinder will ensure its optimum performance. Make a habit of inspecting your grinder each time you use it. Check for the following conditions and repair or replace when necessary: • Loose fasteners. • Worn switch. • Worn or damaged cords and plugs. • Any other condition that could hamper the safe operation of this equipment. Keeping Tool Clean The Model G5968/9 Angle Grinder will give you years of trouble free service if you keep it clean and free of built-up dust or grime. Ensure that no air passages get blocked. If they do, blow them out with compressed air. Plastic parts can easily be cleaned with a damp cloth, but never use water to clean any electrical parts. Solvents should also be avoided on plastic because of the possibility of damage. Disassembly and improper reassem- Wear safety glasses when cleaning tool with compressed air. Brushes The brushes need to be checked periodically to ensure optimum performance. If the brushes need to be replaced, simply unscrew the plastic cap on both sides of the grinder back by the trigger. Pull out and inspect the brushes. Either re-install or replace the brushes at this time. Repair and Service All quality tools will eventually wear from normal use. Since the grinder is encased in a double insulated plastic cover, leave repair and service issues to a qualified service technician. Technical Data Model: G5968 G5969 Rated Voltage: 110V 110V Rated Frequency: 60 Hz 60 Hz Rated Power Input: 450W 700W No-Load Speed: 11,000 10,000 RPM RPM bly of this device can result in electrical shock danger. Always have this device serviced by a qualified electrical repair technician. Serious injury will result. G5968/9 Angle Grinder -5 Model G5968 Parts Breakdown 272829303132333435363738394041 26 24 25 23 229 8 21 7 6 5 1 2019 18 17 4243444546 Disc48 50 21 1 10 11 12 13141516 4 3 1 2 -6-G5968/9 Angle Grinder Model G5968 Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION PHTEK14M TAP SCREW M4 X 6 P5968002 BACK COVER P5968003 CORD P5968004 CORD GUARD P5968005 CAPACITANCE P5968006 SWITCH PHTEK15M TAP SCREW M4 X 10 P5968008 HOUSING P5968009 SWITCH ROD LINK P5968010 CHOKE P5968011 PROTECT RING P5968012 TOUCH SPRING P5968013 STATOR PLW02M LOCK WASHER 4MM P5968015 TAP SCREW M4 X 70 P5968016 CORD CLIP P626 BEARING 626-RS P5968018 FAN GUIDE P5968019 ARMATURE P5968020 BRUSH HOLDER P5968021 WOODRUFF KEY #202 P5968022 CARBON BRUSH P5968023 BRUSH CAP P5968024 INNER COVER 25 P626 BEARING 626-RS 26 P5968026 GEAR 27 P5968027 SPINDLE LOCK 28 P5968028 SPRING 29 PHTEK16M TAPSCREW M5 X 25 30 P5968030 GEAR HOUSING 31 P5968031 BRAKE PIN 32 P5968032 BEARING 8E8*12*10 33 PR05M EXT RET RING 15MM 34 P5968034 GEAR 35 P5968035 RETAINING PLATE 36 P6201 BEARING 6201-2RS 37 P5968037 ASPHALT FELT 38 PW05M FLAT WASHER 4MM 39 P5968039 PACKING GLAND 40 PLW02M LOCK WASHER 4MM 41 PS02M PHLP SCR M4-.7 X 12 42 P5968042 SPINDLE 43 PS02M PHLP SCR M4-.7 X 1...
Este manual também é adequado para os modelos :Máquinas e acabar - G5968 (213.02 kb)