Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
6. 5. When using a depressed-center wheel, hold the tool so that an angle of approximately 30° exists between the wheel and the work. WARNING: Check rated speed on depressed-center wheel. Never use a wheel with rated speed lower than the speed on the nameplate of the tool. FITTING WIRE CUP BRUSHES Wire cup brushes screw directly on the spindle of the machine without the use of flanges. When using wire brushes, thread firmly on spindle by hand. SANDING REMOVING THE WHEEL GUARD (FIG. 7 SANDING ONLY) TURN OFF AND UNPLUG THE TOOL. NOTE: TO PREVENT LOSS OF CONTROL, DO NOT SET TOOL DOWN UNTIL ACCESSORY HAS COMPLETELY STOPPED TURNING. As shown in Fig. 7, place the grinder on a table, spindle up. Rotate the guard in the direction of the arrow until it stops. Use a small screwdriver to depress the locking pin in the slot. While holding the locking pin down with the screwdriver, turn the guard slightly in the direction of the arrow to keep the locking pin depressed. Remove the screwdriver and continue to turn the guard until it is released. PRECAUTIONS TO TAKE WHEN SANDING PAINT 1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women. 2. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we recommend the following precautions when sanding any paint: PERSONAL SAFETY 1. No children or pregnant women should enter the work area where the paint sanding is being done until all cleanup is completed. 2. A dustmask or respirator should be worn by all persons entering the work area. The filter should be replaced daily or whenever the wearer has difficulty breathing. Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more American Wire Gage Than Than 0 - 6 18 16 16 14 6 - 10 18 16 14 12 10 - 12 16 16 14 12 12 - 16 14 12 Not Recommended NOTE: ONLY THOSE DUSTMASKS SUITABLE FOR WORKING WITH LEAD PAINT DUST AND FUMES SHOULD BE USED. ORDINARY PAINTING MASKS DO NOT OFFER THIS PROTECTION. SEE YOUR LOCAL HARDWARE DEALER FOR THE NIOSH APPROVED PROPER MASK. ENVIRONMENTAL SAFETY 1. Paint should be removed in such a manner as to minimize the amount of dust generated. 2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness. 3. Sanding should be done in a manner to reduce tracking of paint dust outside the work area. FITTING ABRASIVE DISCS TURN OFF AND UNPLUG THE TOOL. Use an abrasive disc with a backing pad for sanding with your angle grinder. 1. Remove the guard. 2. Place the flange, (backing pad and abrasive disc sold separately) and outer flange on the spindle as shown in Figure 8. Figure 8A shows how to attach an abrasive disc with a rubber backing pad. 3. Tighten the abrasive disc as shown in Figure 9 by depressing the spindle lock button and turning the abrasive disc by hand. GENERAL INFORMATION HELPFUL HINTS • Hold your angle grinder with one hand on the body and the other hand firmly around the side handle as shown in Figure 10. • Always position the guard so that as much of the exposed disc as possible is pointing away from you. • Be prepared for a stream of sparks when the disc touches the metal. • Maintain an angle between the disc and work surface (Fig. 11) of approximately 30° when grinding and 10°-15° when sanding ( Fig. 12) for best tool control, material removal, and minimal loading. WARNING: Always wear eye protection while operating this power tool. TOOL MAINTENANCE CLEANING: Blowing dust and grit out of the motor housing using compressed air is a necessary maintenance procedure. Dust and grit containing particles from metal grinding often accumulate on interior surfaces and could create an electrical shock hazard if not cleaned out. LUBRICATION Black & Decker tools are properly lubricated at the factory and are ready for use. Tools should be lubricated regularly every year depending on usage. (Tools used on heavy duty jobs and tools exposed to heat may require more frequent lubrication.) This lubrication should be attempted only by trained power tool repairperson's such as those at Black & Decker service centers or in other qualified service personnel. IMPORTANT To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be performed by Black & Decker service centers or other qualified service personnel, always using Black & Decker replacement parts. ACCESSORIES Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800- 54-HOW-TO (544-6986). WARNING: The use of any accessory not recommended for use with this tool could be hazardous. SERVICE INFORMATION Black & Decker offers a full network of company-owned and authorized service locations throughout North America. Al...
Este manual também é adequado para os modelos :Máquinas e acabar - Fire Storm FS6500AG (218.48 kb)