Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
3) • Place the sanding base (10) onto the spindle (6). • Place the washer (7) onto the spindle. • Insert the allen screw (8) into the screw hole in the spindle. • Tighten the allen screw using the hex wrench (9) supplied. • To remove the sanding base, remove the allen screw (8) and washer (7). Fitting sanding sheets (Fig. 4) • Detach the two diamond-shaped tips (11) from the sanding sheet (12). • Hold the tool with the sanding base facing upwards. • Place the sanding sheet (12) onto the sanding base making sure the holes in the sheet line up with the holes in the base. Diamond-shaped tips (Fig. 5) The diamond-shaped tips (13) can be reversed and replaced when worn. • When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again. • When the whole tip is worn, remove it from the sanding base and fit a new tip. Finger base The finger base is used for fine detail sanding. The base attaches and removes the same as the round and large detail bases. The tips can be reversed and replaced when worn. Polishing bonnet and foam pad The polishing bonnet and foam pad attach to the round random orbit base. With the bonnet and pad, you can use the tool as a random orbit polisher. Fitting and removing the polishing bonnet and foam pad (Fig. 6) • Hold the tool with the round base facing upwards. • Place the bonnet or pad (14) onto the base making sure that it is centered. OPERATION Let the tool work at its own pace. Do not overload. Switching on and off (Fig. 7) • To switch the tool on, press the part of the on/off switch (1) marked “I”. • To switch the tool off, press the part of the on/off switch (1) marked “0”. Emptying the dust cassette (Fig. 8) The dust cassette should be emptied after every 10 minutes of use. • Pull the dust cassette (2) to the rear and off the tool. • Hold dust cassette with the outlet facing down and shake the cassette to empty the contents. • Refit the dustbag onto the tool. Dust Collection WARNING: Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty bag frequently and strictly follow sander manual and coating manufacturer's instructions. CAUTION: When working on metal surfaces, do not use the dustbag or a vacuum cleaner because sparks are generated. Wear safety glasses and a dustmask. Due to the danger of fire, do not use your sander to sand magnesium surfaces. Do not use for wet sanding. Sanding Lead Base Paint Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we recommend the following precautions when sanding any paint: Personal Safety • No children or pregnant women should enter the work area where the paint sanding is being done until all clean up is completed. • A dust mask or respirator should be worn by all persons entering the work area. The filter should be replaced daily or whenever the wearer has difficulty breathing. NOTE: Only those dust masks suitable for working with lead paint dust and fumes should be used. Ordinary painting masks do not offer this protection. See your local hardware dealer for the proper (NIOSH approved) mask. • NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work area where dust would settle on them. Environmental Safety • Paint should be removed in such a manner as to minimize the amount of dust generated. • Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness. • Sanding should be done in a manner to reduce tracking of paint dust outside the work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Polishing NOTE: Although this discussion deals with polishing a car, your Multi-Tool is capable of polishing a wide array of flat surfaces such as hardwood floors, furniture, boats and other surfaces that could use an occasional shine. For best results, follow these simple steps to get a really professional looking job: 1. Wash The Car Wash the car with a mild detergent solution, by hand, starting on top surfaces and working down the sides. As each area is completed, rinse it thoroughly with clean water. Remove any buildup of road tar, insect spots and other foreign matter from the car using commercially available special cleaners. Use these cleaners only by hand. Make sure car surfaces are completely dry before starting to polish the car. NOTE: Do not polish any car in direct sunlight or when the body is hot. 2. Apply Liquid Wax Apply a small amount of liquid wax t...