Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
per Minute 1,2,3, ... Ring Selector Settings Speed, Torque or Position Settings FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. ON/OFF Switch with Locking Tab 2. Tool Body 3. Protective Guard 4. 9" Grinding Wheel 5. Spindle Lock Button 6. Power Cord ACCESSORIES: 7. Side Handle 8. Pin Spanner 9. Hex Wrench 10. 7" Grinding Wheel I COMPONENT MODEL NUMBER I Pin Spanner 690157 ASSEMBLY A CAUTION Make sure you have full control of the tool when grinding into a comer as a sharp, sudden movement may occur when the wheel contacts a secondary surface. 9 ATTACHING AUXILIARY HANDLE (Ci This tool comes with an auxiliary handle which can be attached to the left, right or top side of the Angle Grinder, depending on the preference of the operator. This handle is necessary to maintain complete control of the tool and should be used at all times. Make sure this handle is always fastened securely. ATTACHING WHEEL GUARD A CAUTION Never brush or grind without the guard in place. Brushes are considered to be grinding wheels and must also be used with guards. • Always unplug the tool before attempting to change the guard or accessories. • Set the Angle Grinder on a flat surface with the spindle facing up. • Place the spring washer of the guard over the spindle. • Tighten the screw of the spring washer. • Make sure that the guard is securely tightened in place. NOTE used in a 9" guard. Wheel size MUST match guard size. A 7" wheel may not be ATTACHING WHEELS WITH DEPRESSED CENTERS A WARNING Always check the tool warning label for the recommend-n accessories. Never run a wheel or brush over the rated exceeding the recommended speed may fly apart and cause jury. ed speed rating o speed. Accessories serious personal in NOTE Hubbed wheels do not require mounting flanges. • When working with thick grinding wheels, fit the threaded outer flange with the raised area facing away from the wheel. • Push in the spindle lock button. Turn the outer flange until it locks into place. • Once the spindle is locked, insert the enclosed wrench into the holes of the outer flange to tighten the outer flange properly. Check to make sure that the guard is fitted properly. Put the inner flange on the spindle. Put the grinding wheel on the spindle and the inner flange. When working with thin grinding wheels, fit the threaded outer flange with the raised area facing toward the wheel. 11 ATTACHING WIRE BRUSHES Wire cup brushes, not included, can be screwed directly on the spindle. No flanges are necessary. EDGE GRINDING A WARNING qo n0( use edge grinding wheels lor cut-off woric, deep grinding or subject them to any side pressure as this may lead to breakage and possible personal injury. These wheels should be used for shallow cutting and notching (less than 1/2" in depth). Keep the open side of the guard away from the operator at all times._ Edge grinding should only be done with wheels specifically designed for this purpose. REMOVING GUARD FOR SANDING OR USING FLAT WIRE BRUSHES • Set the Angle Grinder on a flat surface with the spindle facing up. • Remove the inner and outer flanges, unscrew spring washer and remove the guard. • Store these parts carefully. • Replace the guard after the job is finished. ATTACHING SANDING DISC • To remove the guard, see instructions given in the "Removing Guard for Sanding or Using Flat Wire Brushes" Section above. • Set the inner flange and outer flange on the spindle. • Push in the spindle lock button. Turn the spindle until it locks into place. • Once the spindle is locked, tighten the sanding disc by hand. OPERATING THE ANGLE GRINDER A WARNING juard or accessori Always unplug the tool before attempting to change the es. NOTE oading, keep the a y 30° when grindir For best tool control, material removal and minimal ngle between the disc and the work surface at approximate-lg and 10°-15° when sanding. 12 OPERATING THE ON/OFF SWITCH A WARNING under load conditi Never switch the Angle Grinder "ON" or "OFF" while ons. A CAUTION Always allow the Angle Grinder to come up to full speed before touching any surface. Always take the tool away from the workpiece before turning the tool "OFF". Let the tool come to a complete stop before setting it down. This tool operates best under light pressure. Exerting heavy pressure will not speed up the work and may cause damage to the motor. ON/OFF SWITCH When starting, hold the tool firmly with both hands. (One hand on the rear handle or motor housing and the other on the side handle.) To start, push the "On/Off" switch forward, then press down slightly. To stop, release the "On/Off" switch. ROTATING THE REAR HANDLE A WARNING guard or accessories. Always unplug the tool before attempting to change the Unlock the rear handle by pressing the handle release button. Rotate handle into available left or right position of center. Before turning tool "ON", ensure that the handle is locked into a pos...