11/3 HP BELT/DISC SANDER BD1500 INSTRUCTION MANUAL 1/3 HP BELT/DISC SANDER BD1500 INSTRUCTION MANUAL ContentsContents Introduction 3 Description of symbols 3 Specifications 3 General safety rules 4 Additional safety rules for belt & disc sanders 5 Unpacking 6 Accessories 7 Know your product 8 Getting to know your belt and disc sander 9 Mounting belt and disc sander to workbench 9 Installing sanding disc and guard 9 Installing work support 9 Installing table assembly 10 Auxiliary mounting for ver

This angle grinder is designed as a dry grinder/cutter. Failure to observe this warning could result in a fatal shock. Holding and guiding the tool 1. Always clamp the workpiece. 2. Do not overload the tool so that the disc slows down. Let the tool do the work rather than applying pressure. The weight of the tool alone provides sufficient pressure. 3. Cutting and grinding discs become very hot when in use. Take care not to touch them until they have cooled down. 4. Hold the tool securely and mak

Use of the power tool for operations different from intended could result in a hazardous situation. Service • Have your power tool serviced by a qualified repair personnel using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Additional safety rules for angle grinders • Fully unwind cable drum extensions to avoid potential overheating. • When an extension cable is required, you must ensure that it has the right ampere rating for your power tool

Wear goggles Wear ear defenders Wear a breathing mask 5 Contents of carton The GMC ROS400A Random Orbital Sander is supplied with the following accessories as standard: • 5 x 80 grit hook & loop sanding sheets • Dust bag • Instruction manual Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure

The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design: • Damage to the lungs if an effective dust mask is not worn. • Damage to hearing if

1. Turn the sander upside down and remove the four hex screws using the hex key (9) provided. Take off the base assembly. 2. Place the replacement base assembly on the tool and secure it with the 4 hex screws using the hex key (9) supplied. Fitting a sanding sheet WARNING. Always ensure that the tool is switched off and the plug is removed from the power point before making any adjustments or maintenance procedures. 1. Before fitting sandpaper, remove any dust or debris from the base. 2. Match t

The following hazards may arise in connection with the tool’s construction and design: 5 • Damage to the lungs if an effective dust mask is not worn. • Damage to hearing if effective earmuffs are not worn. • Always remove the plug from the mains socket before making any adjustments or maintenance, including changing the sandpaper. Wear goggles Wear earmuffs Wear a breathing mask Contents of carton The GMC KAT150B SandKat Detail Sander is supplied with the following accessories as standard: • 10

• Replace a cracked or suspect wheel. • Always allow a new wheel to run for a few minutes at full speed before using it. Stand to one side at start up. • Check that the wheel rotates freely each time before start up. • Do not use the grinder unless all the guards are properly fitted and secure. • Check that the tool rests are properly adjusted before commencing use. • Do not overload the grinder. Allow the grinder to run at full speed, or close to full speed during use. • Never apply excessive p

• Frequently clean grinding dust from beneath grinder. • Always remove the plug from the mains socket before making any adjustments or maintenance, including changing the wheel. • Always wear eye protection and check that the eye shields on the grinder are properly adjusted. • Always turn the grinder off when it is not in use and never leave it unattended without first switching off and removing the power plug. Never leave the grinder until the grinding wheels have come to a complete stop. • Mak