Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
The 831E is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. The receiver is powered from the operator’s 24 VAC transformer. The antenna is removable and may be moved (using coaxial cable) to a new location for better RF reception. When receivers have to be installed in close proximity to each other (such as Fire Stations), master/slave units may be used to reduce the potential for receiver cross-talk. • ALLSTAR 831E RECEIVERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY. DO NOT USE FOR ANY OTHER PURPOSE. DO NOT MODIFY IN ANY MANNER. • CHECK LOCAL BUILDING AND ELECTRICAL CODES FOR MANDATORY INSTALLATION AND WIRING REQUIREMENTS. • CONNECT POWER CORDS ONLY TO A PROPERLY GROUNDED OUTLET. IF PERMANENT WIRING IS REQUIRED BY CODES, DISCONNECT POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE ATTEMPTING ANY WIRING CONNECTIONS. • DO NOT WEAR RINGS, WATCHES OR LOOSE CLOTHING WHILE INSTALLING OR SERVICING GARAGE DOOR OPENERS. WEAR SAFETY GOGGLES OR OTHER PROTECTIVE EYEWEAR. • AN UNBALANCED DOOR OR ONE THAT STICKS OR BINDS MAY CAUSE INJURY OR DEATH. ENSURE DOOR IS PROPERLY BALANCED AND ELIMINATE ANY STICKING OR BINDING. • YOUR GARAGE DOOR IS A LARGE MOVING OBJECT. THE SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE UTILIZED TO BALANCE ITS OPERATION ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SERIOUS PERSONAL INJURY, EVEN DEATH, IF DISTURBED. ONLY A QUALIFIED SERVICE PERSON SHOULD MOVE, LOOSEN OR ADJUST DOOR SPRINGS OR HARDWARE. • LOCATE CONTROL PUSHBUTTONS WITHIN SIGHT OF THE DOOR AND AWAY FROM THE MOVING PARTS OF THE DOOR. INSTALL ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL PUSHBUTTON IN A PROMINENT LOCATION. • REMOVE ALL ROPES AND REMOVE OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR. • THE IMPORTANT SAFEGUARDS AND INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS. IT MUST BE UNDERSTOOD THAT COMMON SENSE AND CAUTION MUST BE EXERCISED BY THE PERSON(S) INSTALLING, MAINTAINING AND OPERATING THIS EQUIPMENT. INSTALLER: Leave this manual with your customer upon completion of the installation. WARNING TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS! PRODUCT FEATURES IMPORTANT INSTALLATION NOTES Page 2 of 4 P/N 106547 REV D The 831E receiver functions as a 3-button station. Three sets of isolated contacts are provided; normally open contacts for the OPEN PUSHBUTTON (orange wires); normally open contacts for the CLOSE PUSHBUTTON (black wires); normally closed contacts for the STOP PUSHBUTTON (gray wires). Refer to Figure 1. For special STOP circuit applications, normally open contacts are available from the factory. Typical 4-wire 3-button stations are wired as shown in Figure 2. Number 18 gauge wire or heavier must be used for wiring the control stations and the 831E receiver to the door operator. Smaller gauge wire may cause operational problems, especially when multiple 3-button stations are used. For typical installations the 831E receiver is mounted near the door operator, away from any high voltage conduits or steel support beams. For wiring, follow the steps below and refer to Figure 3. 1. In the door operator control panel, locate the wire connecting the door operator to the 3-button station COMMON. Note its location and remove. 2. Connect one of the gray wires from the 831E to the wire just removed from the pushbutton COMMON. 3. Connect the following wires from the 831E to the operator 3-button COMMON (as shown at right): ONE ORANGE (OPEN) ONE BLACK (CLOSE) ONE GRAY (STOP) 4. Connect the remaining 831E black wire to the CLOSE pushbutton terminal in the door operator control panel. 5. Connect the remaining 831E orange wire to the OPEN pushbutton terminal in the door operator control panel. 6. Finish the wiring by connecting 24 VAC to the red and white wires of the 831E receiver. BEFORE APPLYING POWER, CHECK ALL CONNECTIONS AND INSTALL THE ANTENNA. IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY. FOLLOW LOCAL BUILDING AND ELECTRICAL CODES. WARNING TO PREVENT ELECTROCUTION DISCONNECT POWER AT FUSE BOX AND DOOR OPENER BEFORE WIRING PERMANENTLY. WARNING DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS PROPER ENTRAPMENT PROTECTION DEVICES ARE INSTALLED. CONSULT THE MANUFACTURER OF YOUR OPERATOR FOR MORE DETAILS. WARNING 831E COMMERCIAL RECEIVER WIRING INSTRUCTIONS STOP CLOSE OPEN TERMINAL STRIP TO OPERATOR WALL PUSHBUTTON STATION Figure 2 105113 COMMERCIAL STOP COM OPEN CLOSE OPERATOR RECEIVER MVP-831E OPEN STOP CLOSE WALL PUSH BUTTON ORANGE BLACK GRAY BLACK GRAY ORANGE WHITE RED COMMON 24 VAC Removed Wire (See Step 1) Step 2 Step 3 Step 4 Step 5 Step 6 STATION Figure 3 106549 RED WHITE GRAY BLACK ORANGE 24 VAC CLOSE STOP OPEN 831E RECEIVER Page 3 of 4 P/N 106547 REV D The 831E receiver may be used with many different Allstar transmitters. The information below indicates how to set the coding switches i...