Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
SECTION 3. LEARN THE STITCHES = Use the Darning Plate Sometimes when you sew, you want to contro the fabric youself. The Darning Plate covers the feed dogs so that they do not touch the fabric. To Put on the Darning Plate: NOTE: The rectangular holes in the Darning Plate match the holes in the needle plate. In the darning plate, these holes are slightly to the left of center. 1. Position the darning plate with the 3 pins on the bottom. 2. Fit the darning plate pins into the needle plate holes. The feed dogs will show through the darning plate holes. Use the darning plate in the following ways: Darning (P. 22) Button Sewing (P. 26) • Darning f Set the Machine Stitch Stitch selector I I I (Model 12614) Top thread tension control 1 to 4 (Model 11607) Stitch length control any number (not necessary to Here's How adjust) 1. Put the darning plate on the needle plate (see p. 22). No presser foot 2. Remove presser foot and stretch fabric Darning plate between embroidery hoops with hole centered. 3. Draw the bobbin thread up through the fabric by holding the top thread and taking one stitch at the spot where you wish to start darning. 4. Lower the presser bar and sew at a slow speed. 5. Move the fabric back and forth slowly until you have covered the darning area. 6. Turn the fabric a half turn and sew another layer of stitching over the first layer. NOTE: If your fabric is thin or badly damaged, use a separate piece of fabric under the hole to reinforce it. 7. When you finish darning, remove the darning 22 plate. SECTION 3. LEARN THE STITCHES Zigzag Stitches • Basic Zigzag f Set the Machine Stitch Stitch selector ........iii:ii!i!ii! i!i! i. (Model 12614) Top thread tension control 2 to 5 (Model 11607) Stitch length control red Here's How zone There are many ways to sew a zigzag stitch. Consult the specific variations for detailed directions. Zigzag foot Satin Stitch p. 24 i C Applique Work p. 25 Bar Tacking p. 25 Button Sewing p. 26 Overcasting p. 22 Three-step zigzag p. 28 The Stitch and Its Uses Rick-rack stretch p. 3j Overcast stretch p. 3_22 The zigzag stitch common and most is one of the most versatile stitches on Serging p. 333 your machine. It can be a utility stitch for sewing buttons, buttonholes, hemming, overcasting, mending and darning. It can also be used to decorate with trims, appliques and cut-out work or as a decorative stitch. 23 SECTION 3. LEARN THE STITCHES • Satin Stitch Set the Stitch Machine Stitch selector Close to 0 Zigzag width : (Model 12614) Top thread tension control 1 to 4 I_lllt_t L__J (Model 11607) Stitch length control 0.5 to 1 Stitch length : > Satin stitch foot The Stitch and Its Uses The Satin stitch is a versatile and often used decorative stitch, but t can also be used to overcast a raw edge (for example, blankets, linens, tablecloths and napkins). The Satin stitch is especially attractive in applique. Here's How Once your machine the fabric you are weight fabrics. is set up to stitch, you may want planning to use. Too tight a satin to experiment on a scrap of stitch may pucker some light SECTION 3. LEARN THE STITCHES Zigzag Stitches (Continued) ® Appliq ue Set the Machine Stitch Stitch selector (Model 12614) Top thread tension control 1 to 4 (Model 11607) Stitch length L 1 control 0.5 to 1 Baste (or fuse with ron-on fabric joiner) applique pieces on the fabric. Stitch around the applique making sure the needle falls along the outer Zigzag foot edge of the applique. When sewing corners, lower the needle down into the fabric, Raise the presser foot and pivot the fabric to the right or left. Bar Tacking Set the Machine Stitch Stitch selector (Model 12614) Top thread tension control 1 to 4 Satin (Model 11607) Stitch length control 0.5 to stitch foot 1 J This stitch is similar to a very short satin stitch and is used to reinforce points of strain such as corners or pockets and straps on lingerie. Sew 4 to 6 zigzag stitches. SECTION 3. LEARN THE STITCHES ® Sew a Button Set the Machine Stitch Stitch selector ,/ z (Model 12614) J Top thread tension control 1 to 4 Zigzag foot (Model 11607} Stitch length control any numoer (not necessary to adjust) Darning plate Use 1. 2. 3. 4. 5. the darning plate for button sewing (see p. 22). I ptSet the stitch selector at " c_ • Align both holes of the button with the slot hole of the button just below the needle point. Lower the foot and turn the stitch selector to comes just above the right hole of the button. Sew about five stitches and raise needle. i Set the stitch selector at " c_ " again and sew of the foot and place the left zigzag unti the needle point a few stitches to lock thread. f J To strengthen the shank, cut the threads leaving a 20 cm (8") tail. Bring the needle thread down through the hole ir the button and wind it around the shank. Draw the thread to the bottom side and knot. SECTION 3. LEARN THE STITCHES Zigzag Stitches (Continued) = Overcasting Stitch f Set the Machine Stitch Stitch selector (Model 12614) Top thread tension I_l...
Este manual também é adequado para os modelos :Máquinas de costura - 385.11607 (3.01 mb)