Assessments - 3, GPA: 4 ( )

Fabricante : Kenmore Arquivo Tamanho: 8.01 mb Arquivo Nome : Língua de Ensino:

Insufficient pressure may cause poor feeding of the fabric, skipped stitches, or difficulty in guiding the fabric. If feed dogs or presser foot marks appear on the fabric, reduce the pressure. When sewing multiple thickness or heavy fabric, reduce the pressure. Increase pressure when sewing lighter weight fabrics. FEED DOG CONTROL There are a few times when you want to control the feeding of the fabric yourself. Remove the base cover from the base. Pull down the feed dog control or turn to the left as shown in Fig. 1. The feed dogs will drop. You may then determine the movement of the fabric yourself. For most of your stitching, the feed dog control should be in the up position. Whenever you raise or lower the feed dogs, be sure to have the presser foot in the up position. SEWING LIGHT The light and power switch shown in Fig, 1 and 2 provides the electric current for the motor as well as for the light. In order to operate the machine, this switch must be on. To turn on the light, depress the upper side of the switch. If you are interrupted while sewing and must leave the machine unattended, just turn off the switch and the machine cannot be started accidentally. The sewing light is located inside the face cover plate as shown. To replace the bulb, turn light off, and swing the face cover plate open. Push up on the bulb slightly and turn bulb clockwise. Remove bulb from socket. Push in new bulb and turn counter-clockwise. 3 1R NEEDLE PLATE INSERTS (Free-arm type) You are provided with two needle plate inserts: A. Needle plate with wide oval hole for all zigzag stitching. B. Needle plate with round hole for regular straight stitching and straight stretch stitch sewing. CHANGING NEEDLE PLATE INSERTS 1. Raise needle to its highest position and raise presser foot. 2. Swing shuttle cover open. 3. Push a spring under the plate as shown to release the needle plate insert. 4. Remove needle plate insert by placing thumb under edge of plate. 5. Replace the needle plate insert positioning as shown in Fig. 3. 6. Push needle plate insert down to lock into place, Reposition the shuttle cover. SEAM GUIDES Seam guides are printed on either side of the needle plate to aid you in guiding your fabric, THE GUIDE LINE EXTENDING ABOVE THE RIGHT SIDE OF THE NEEDLE PLATE IS THE "ALL IMPORTANT" 5/8'" SEAM LINE. The cornering guides are convenient when turning a square corner 5/8" from the fabric edge. See next section of this book for directions. MULTI PURPOSE NEEDLE PLATE (Flat-bed type) This multi purpose needle plate provides a small round hole for straight stitching and a wide oval hole for zig zag and decorative stitching. CHANGINGMULTI PURPOSE NEEDLE PLATE 1. Raise needle to its highest position and raise presser foot. 2. Open hand hole cover plate. 1 Remove multi purpose needle plate by placing thumb under edge of plate and lifting it up and out. * Reverse and reposition the needle plate as shown. . Lock it into place by fixing hand hole cover plate in position. SEAM GUIDES Seam guides are printed on either side of the needle plate to aid you in guiding your fabric. THE GUIDE LINE EXTENDING ABOVE THE RIGHT SIDE OF THE NEEDLE PLATE IS THE "'ALL IMPORTANT" 5/8" SEAM LINE. The cornering guides are convenient when turning a square corner 5/8" from the fabric edge. See next section of this book for directions. ;)0 ACCESSORIES NEEDLES Use KENMORE needles. The size of the needle should conform with the size of the thread and both should be suitable to the fabric (See next page). Never use a bent needle or one with a blunt point. Fig. 1. shows you the exact length of your needle. Be sure you never use one in your machine that is not this exact length. You will find among your accessories "Q NEZI_LES",.with blue shanks. These special needles are to be used when sewing, certain knits and certain difficult synthetic fabrics. If you experience skipped stitches in any of your sewing, use -o NEEDLE",.. PLACEMENT OF NEEDLE Raise needle bar to its highest position by turning the hand wheel toward you. Loosen the needle clamp screw. Holding the needle with the flat side away from_you, slip the needle into the needle bar. Make certain it is up as far as it can go. Tighten the needle clamp screw-with a screwdriver. If you have a double needle for decorative stitching, it is inserted in the same manner as the single needle. NEEDLE, THREAD AND FABRIC CHART O r) PRESSER FEET SUPER-HIGH BAR TYPE Simply drop the presser foot lock and slip the foot away from the presser bar. To aid you in the placement of the presser foot, the presser foot lever can raise the foot beyond the normal "'up" position. After the foot is placed on the presser bar, lift the lock as high as it will go to hold the foot securely. SNAP-ON TYPE Raise the presser bar to its highest position by lifting the presser foot lever. Press the toe of presser foot upward as high as it will go and foot is released. Place the desired foot on the needle plate aligning the needle holes and low...

Baixe o seu

Para fazer o download, introduza 2 dígitos :