Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Portable Sewing Machine will become a valuable tool that will keep your family’s wardrobe in shape. Although not designed to make complicated clothing from scratch, it provides a durable LockStitch to complete your basic mending jobs quickly and with a quality stitch. This machine was specifically designed to be lightweight for easy portability. We are confident you will enjoy the time you spend using our product. Top Innovations, Inc. would like to invite you to take advantage of our customer support web site at Here you will find additional information about the many other exciting Sew Pro and Steam Fast products that are available. We take pride in our quality line of garment care and steam cleaning products and hope you will visit our web site to review our product line. Portable The Benny Lee Chairman & CEO, Top Innovations, Inc. CONTENTS SAFETY INSTRUCTIONS 2 PARTS LISTING 3-4 ACCESSORIES 4 WINDING A BOBBIN 5 THREADING THE BOBBIN 6 INSERTING THE THREADED BOBBIN CASE 6 REMOVING BOBBIN & BOBBIN CASE 7 THREADING THE MACHINE 8 RAISING THE BOBBIN THREAD 9 ADJUSTING THREAD TENSION 10 START TO SEW—HANDHELD OPERATION 11 START TO SEW—TAPLE-TOP OPERATION 12 SECURING A SEAM; DARNING 13 TURNING A SQUARE CORNER 14 CHANGING NEEDLES 14 HOW TO REPLACE THE SLIDE PLATE 14 PERFORMANCE CHECKLIST 15 IMPORTANT SAFETY INSTRUCTIONS WHEN USING THIS MACHINE, THE FOLLOWING BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED: x DO NOT USE WITH BENT NEEDLE. x WHEN SEWING, KEEP FINGERS AWAY FROM ALL MOVING PARTS. SPECIAL CARE IS REQUIRED AROUND THE NEEDLE. x CLOSE ATTENTION IS NECESSARY WHEN THE MACHINE IS USED BY OR NEAR CHILDREN. x WHEN THREADING OR CHANGING A NEEDLE, ALWAYS SWITCH OFF THE POWER SUPPLY. x NEVER PRESS OR PULL THE NEEDLE ARM DIRECTLY, ALWAYS USE THE HAND WHEEL TO MOVE IT. PARTS LISTING PARTS LISTING 1. On/Off Switch 2. Dust Cover 3. Thread Tension Dial 4. Needle Arm 5. Needle Clamp Screw 6. Presser Foot 7. Slide Plate 8. Needle Plate 9. Pretension Stud 10. Spool Pin 11. Spool Holder Ring 12. Spool Stand 13. Hand Wheel 14. Battery Access ( 4 AA Batteries not included) 15. AC Adaptor Socket Rating: Input: 120V/ 60Hz Output: 6 VDC, 600mA 16. Foot Switch Socket PARTS LISTING (cont’d) PARTS LISTING (cont’d) 17. Accessories Storage 22. Take-Up Lever 18. Bobbin Winder Cover 23. Thread Guide Wire Loop 19. Bobbin Winder 24. Bobbin Case Holder 20. Bobbin Winder Thread Guidepost 25. Bobbin Case 21. Presser Foot Lift Lever 26. Bobbin ACCESSORIES 1. Bobbin x4 (1 in Machine) 5. Thread Spool (On Machine) 2. Needle Threader 6. Foot Switch 3. Needle x2 (1 in Machine) 7. Stabilizer (Table Top Operation) (Regular Needle No. 14 for General Sewing) 4. Spool Holder Ring (On Machine) 8. Bonus AC Adapter WINDING A BOBBIN x Place spool of thread onto spool pin. x Press spool holder ring against spool. CAUTION: Spool of thread should be rotated freely afterpressing the holder ring on. x Lead thread to Guidepost (1) and draw to the left under pretension stud (2). x Draw thread between the two tension discs of thread tension dial, then pull thread to right as shown. x Follow arrows. Guide thread through guidepost (3). x Open the bobbin winder cover and insert a bobbin. x Align the small bobbin hole on pin of bobbin winder. x Follow arrows. Manually wind thread clockwise around the bobbin 3-5 turns, then pass thread through the notch. x Still holding end of thread, push on/off switch and start to wind x Trim the end of the thread after bobbin is wound around a few times. (5-10 winds) x Continue to wind bobbin until desired amount is reached and cut thread. CAUTION: Do not over-wind bobbin. Over-winding causes thread jamming of bobbin case. THREADING THE BOBBIN x Use needle threader to pull bobbin thread (bottom) from inside of bobbin case hole x Position bobbin in bobbin case and draw 2-3 inches of thread. You will feel thread tension force while drawing. CAUTION: Bobbin case tension was preset at factory and is not adjustable. INSERTING THE THREADED BOBBIN CASE x Be sure that the bobbin winder cover is closed, raise needle to its highest position by turning hand wheel counter clockwise. x Fully open slide plate, and make sure bobbin case holder is parallel to presser foot edge by rotating hand wheel slightly. x Position and place threaded bobbin case as per graphics shown on slide plate recess. x Slide the bobbin case forward into the bobbin case holder as arrow shown. x Pull thread 2-3 inches to the front. x Replace slide plate. REMOVING BOBBIN & BOBBIN CASE x Be sure that bobbin winder cover is closed, raise needle to highest position by turning hand wheel counter clockwise. x Fully open slide plate, make sure bobbin case holder is parallel to presser foot edge by rotating hand wheel slightly. x Shake machine head to throw the bobbin case out from its recess. x Using a pin, insert into the hole at the bottom of the bobbin case and push bobbin out of bobbin case. THREADING THE MACHINE x Place spool of thread onto spoo...