Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Shredding paper: • Feed paper into the paper infeed opening (see „Technical data“ for sheet capacity) • The shredding pro cess is started by a pho to –cell in the paper feeding opening • App rox. 3 sec. af ter the last sheet of paper is pulled in the cut ting sy stem au to ma tical ly swit ches off and returns to standby. The document shredder can also be started by pressing the green arrow button: • Press briefly: Cutting device starts. Automatic stop approx. 3 seconds after the last piece of paper was drawn in, or manual stop when the stop button is pressed • Hold down for longer than 2 seconds: constant operation without light barrier function. The cutting device runs until it is switched off with the stop button. Destroying credit cards, CDs, discs or DAT cassettes: Cross cut machines: Fold the safety element down (only for cutting types 3.9 x 50 mm and 1.9 x 15 mm), switch the machine on to continuous operation and feed the material into the insertion slot. only for cutting type 3.9x50 mm 3.9x50 mm • 1.9x15 mm Floppy disks Credit cards • CDs only for cutting type 3.9x50 mm DAT cassettes For strip cut machines, feed the CDs, credit cards or discs directly into the paper feed slot. Switching the paper shredder off 0 I • Set mains switch at rear of paper shredder to „0“. 0603 english 11 Paper shredder HSM 411.2 6. Troubleshooting Pa per jam You have fed in too much paper. • Paper shredder jammed. • Red LED in the key pad flashes. • Paper shredder reverses automatically. • Pull paper out of the paper feeding opening. If material is not completely pushed out, then • Press dashed arrow button. • Paper is pushed out. • Pull paper out. The cutting device is easily accessible once the inspection door on the top of the machine is opened. CAUTION! Injuries by cutting rollers are possible even when the paper shredder is idle. Keep hands away from the cutting system! • Separate paper stack and feed paper again. • The shredding process is started again with the green arrow button or by the light barrier (paper feed). CAUTION ! Do not press dashed arrow button and green arrow button alternately forwards and backwards. Cutting system can be damaged. Electric motor overheated • Red LED on membrane keyboard lights. • Paper shredder switches off automatically. • Allow paper shredder to cool down for approx. 15 to 20 min. Front door or inspection door on the top of the machine is open. • Red LED on membrane keyboard lights. • Paper shredder stops automatically. • Close front door and inspection door • If the door is opened when the cutting device is running, the document shredder must be started again using the green button after the door of the document shredder has been closed. Bag for shredded material full • Red LED on membrane keyboard lights. • Paper shredder stops automatically. Reversing the cutting device (“Reverse” button) is also possible even when the shredded material container is full. • Insert new bag Particle cutting devices are equipped with a compacting mechanism. Press the foot pedal in the lower part of the cabinet to shake up the collector sack and reduce the volume of the particles. Paper can be fed again. CAUTION! Empty the shredded material container after the paper shredder has been switched off, because otherwise malfunctions of the cutting system could occur when the rocker switch is pressed several times in succession 12 english 0603 HSM 411.2 Paper shredder 7. Maintenance and care Cleaning: • Switch off the shredder, pull out the mains plug. • When cleaning only use a soft cloth and a mild soap-water solution. Never use scouring agents, cleaning fluid, petroleum or thinners. 8. Technical Data When the cutting capacity drops or the noise increases: • Lift the inspection door on the top of the device and spray special cutting block oil on the blade rollers of the cutting device. • Run cutting system forwards and backwards several times without feeding paper. Paper dust and particles are shaken off. Cutting type Strip cut Cross cut Shred size (mm) 5.8 3.9 3.9 x 50 1.9 x 15 0.78x11 1 x 5 Sa fe ty ra ting DIN 32757 – 1 2 2 3 4 5 Level 6* Cutting ca pa ci ty (sheets), DIN A4 70 g/m2 80 g/m2 65 - 67 51 - 53 48 - 50 38 - 40 38 - 40 33 - 35 26 - 28 20 - 22 17 - 19 12 - 14 9 - 10 7 - 8 Weight 74 kg 82 kg Noise level (Idle running/ load) 60 dB(A) / 68 dB(A) 60 dB(A) / 75 dB(A) Cutting speed 100 mm/s 110 mm Lo ading width 400 mm Voltage 230 V, 50 Hz 100 V, 50/60 Hz – 115 V, 60 Hz Power for the maximum number of sheets 2100 W Dimensions W x D x H (mm) 595 x 470 x 990 Volume of shredded material bag 146 l * HSM-specification Technical and optical modifi cations reserved 0603 english 13 Paper shredder HSM 411.2 9. Scope of delivery • Paper shredder, ready for connection, in carton packing, carton on pallet, tied with strapping tape • 5 bags for shredded material • Special cutting block oil (250 ml) • Operating instructions, information sheet on unpacking Acces so ries • Bag for shredded material, order No.: ...